What Is a 3PE Anti-Corrosion Spiral Steel Pipe?
A 3PE anti-corrosion spiral steel pipe is a spiral submerged arc welded steel pipe whose outer surface has been coated with a three-layer polyethylene anti-corrosion system. The base pipe is formed from a steel coil helically wound and welded along both the inside and outside of the seam, which makes large diameters economical, and the coating is then applied over the blast-cleaned surface to isolate the steel from soil, water and stray current.
The combination is widely used for long-distance pipelines because the spiral welded base pipe gives a favourable strength to weight ratio at large diameters while the three-layer coating delivers a durable, damage-resistant barrier that survives handling, trenching and decades of burial.
Coating Layer Structure
| Layer | Material | Thickness | Role |
|---|---|---|---|
| First layer | Fusion-bonded epoxy powder | Not less than 80 to 100 micrometres | Bonds chemically to the steel and blocks oxygen and cathodic disbondment |
| Second layer | Copolymer adhesive | 170-250 micrometres | Couples the epoxy primer to the outer polyethylene shell |
| Third layer | Extruded polyethylene | 1.8-3.7 mm, up to about 3.7 mm for the reinforced class | Mechanical protection, abrasion resistance and moisture barrier |
In the two-layer equivalent, 2PE, the epoxy primer is omitted and the system consists of the adhesive layer and the polyethylene layer, each with the same thickness as in the three-layer version. 2PE is used for less demanding burial conditions and where the cathodic protection design allows it.
The Spiral Welded Base Pipe
| Item | Typical range |
|---|---|
| Outside diameter | 60 mm to 1420 mm; larger sizes up to DN2200 on request |
| Wall thickness | Set by the line pipe specification and the design pressure |
| Base pipe standard | API 5L / ISO 3183 and GB/T 9711 for line pipe service |
| Steel grades | Grade B and the API 5L X42 to X70 range |
| Seam type | Spiral submerged arc welded, inside and outside |
| End finish | Plain, bevelled, or fitted with a joint coating cut-back for field welding |
Spiral pipe is made by uncoiling strip at an angle to the pipe axis so that the resulting weld runs helically around the circumference. Because the seam is a helix, no single point of the weld carries the full hoop stress, and the pipe can be produced in diameters that would be uneconomic in a longitudinally welded or seamless route. The base pipe is hydrostatically tested and inspected before coating so that a coating defect can never mask a pipe body defect.
Production Process
Shot blasting of the bare pipe to remove mill scale, rust and old coating, leaving the surface profile required for adhesion
Medium-frequency induction heating of the pipe to the epoxy application temperature
Electrostatic spraying of the fusion-bonded epoxy powder to form the first layer
Extrusion or spraying of the copolymer adhesive to form the second layer
Side extrusion of the polyethylene sheet and roller wrapping to form the third layer
Water cooling, end cut-back, holiday detection and visual inspection of the full coated length
Applications
3PE coated spiral steel pipe is used for long-distance oil and gas transmission, natural gas distribution stations and city gate lines, district heating mains, sewage and potable water transmission, coal mine drainage and water supply lines, power plant circulating water and cooling lines, chemical plant process pipe, bridge and steel structure piling, and submarine or river crossing sections where an additional concrete weight coating is sometimes applied over the anti-corrosion layer.
Handling, Joining and Inspection
The weak points of any coated pipeline are the field joints and the points where the coating is mechanically damaged during handling. Use padded slings and belt cradles rather than hooks, avoid dragging coated pipe over rock or concrete, and store pipe clear of the ground on timber sleepers. After the girth weld, blast or power-tool clean the bare joint, apply a compatible heat-shrink sleeve or field-applied three-layer tape that overlaps the plant coating on both sides, and holiday test the finished joint. At inspection, verify blast cleanliness, each layer thickness, adhesion at both interfaces, impact and indentation resistance on cut samples, and the absence of holidays along the entire length.
FAQ
Q: What is the difference between 2PE and 3PE coating?
3PE has three layers, an epoxy primer, an adhesive and a polyethylene jacket, while 2PE has two layers, an adhesive and a polyethylene jacket. The epoxy primer in 3PE improves adhesion to the steel and gives better resistance to cathodic disbondment.
Q: Why use spiral welded pipe as the base for a coated line?
Spiral welding makes large-diameter pipe economical and allows long lengths to be produced from coil, which reduces the number of girth welds in the finished pipeline. The helical seam also distributes the hoop stress around the circumference.
Q: What standards govern 3PE coating on spiral pipe?
Common references are ISO 21809-1 for three-layer polyolefin coatings, DIN 30670 for polyethylene coatings, CSA Z245.21, NF A49-710 and GB/T 23257. The base pipe itself is normally ordered to API 5L, ISO 3183 or GB/T 9711.
Q: How thick is the polyethylene layer?
Normal class coating generally runs from about 1.8 mm to 3.0 mm of polyethylene depending on pipe diameter, and the reinforced class up to about 3.7 mm. The project coating specification sets the exact figure for each pipe size.
Q: What is the maximum service temperature of a 3PE coating?
Polyethylene jackets are generally used up to a continuous service temperature in the region of 60 to 80 degrees Celsius. Above that, three-layer polypropylene or an insulated pipe system with an outer casing is specified.
Q: How are field joints protected after welding?
With a heat-shrink sleeve or a field-applied three-layer tape system that overlaps the plant coating on both sides of the joint. The joint is blast or power-tool cleaned first, and the finished field joint is holiday tested.
Q: Can 3PE coated pipe be bent or cut on site?
Coated pipe can be field bent cold within the limits of the base pipe specification, but the coating must be supported to prevent cracking, and cut ends must be re-coated with a compatible field-applied system before backfilling.





