Oct 18, 2024 Leave a message

A134 EFW Steel Pipe: Plate Grades, Seam Welding and Pressure Duty

What ASTM A134 and ASME SA134 Electric-Fusion-Welded Pipe Really Is

ASTM A134 (identical in content to ASME SA134 in Section II Part A of the ASME Boiler and Pressure Vessel Code) is the specification for electric-fusion (arc)-welded steel pipe made from plate. It is the specification used when a project needs a large-diameter, heavy-wall pressure pipe that cannot be produced economically as a seamless tube or as a mill-width ERW coil product. The distinguishing feature is the input material: instead of strip, the pipe is formed from plate that has already been rolled and, in most cases, already tested against its own plate specification.

Three consequences follow directly from that construction. First, the wall thickness of an A134 pipe is a plate thickness, so the dimensional tolerance on the wall is inherited from the plate standard rather than from a pipe mill standard. Second, the chemical composition and the mechanical properties of the pipe body are those of the plate grade, which is why an A134 purchase order must always name both a plate grade and a pipe specification. Third, the weld is a fusion weld with filler metal added - normally submerged arc welding for the longitudinal or helical seam and shielded metal arc or gas metal arc for the closing and repair welds - so the weld metal is a separate material that has to be qualified alongside the plate.

A134 pipe is ordered as straight-seam (single longitudinal seam) or helical-seam (spiral) construction, in nominal pipe sizes that in commercial practice begin around NPS 16 (DN 400), where plate rolling becomes more economic than coil forming, and extend to very large diameters for penstock, plant piping and structural pressure service. Straight-seam pipe is preferred where the seam must be radiographed along its full length in one axis; helical-seam pipe gives better control of diameter for a given plate width and is common in water and slurry lines.

Plate Grades Behind the Pipe: SA-285, SA-515 and SA-516

Because the pipe body is plate, the grade that appears on the mill certificate is a plate grade from ASME Section II Part A. The three families most often used for A134 pipe are SA-285 (low and intermediate tensile carbon steel plate for general service), SA-515 (carbon steel plate for intermediate and higher temperature service) and SA-516 (carbon steel plate for moderate and lower temperature service, including impact-tested applications). Each family is divided into grades by strength level, and the pipe inherits that strength level.

Plate specification Grade Minimum yield strength Tensile range Typical use in welded pipe
SA-285 A 165 MPa (24 ksi) 310–450 MPa (45–65 ksi) Low-pressure water, air and non-hazardous service
SA-285 B 185 MPa (27 ksi) 345–485 MPa (50–70 ksi) General plant piping, low heads
SA-285 C 205 MPa (30 ksi) 380–515 MPa (55–75 ksi) Moderate pressure, larger diameters
SA-515 60 220 MPa 415–550 MPa Elevated temperature service, steam and hot water
SA-515 65 240 MPa 450–585 MPa Boiler and vessel connections, higher temperature
SA-515 70 260 MPa 485–620 MPa Heavy-wall high-temperature headers and drums
SA-516 60 220 MPa 415–550 MPa Impact-tested pressure piping at low temperature
SA-516 65 240 MPa 450–585 MPa Low-temperature gas and liquid lines
SA-516 70 260 MPa 485–620 MPa Most common A134 pressure-service plate grade

The practical difference between SA-515 and SA-516 is not strength but intent. SA-515 is a plate for service at elevated temperature and is normally supplied in the as-rolled or normalized condition with chemistry balanced for creep resistance rather than notch toughness. SA-516 is the impact-toughness plate: its chemistry is tighter on carbon and manganese and it is routinely ordered with a Charpy supplement for low-temperature duty. When a pipeline or a plant line is to operate below 0 °C, the plate grade, the impact test temperature and the absorbed energy requirement must all appear on the order, because A134 itself does not impose a toughness requirement on the pipe body.

Chemical Composition and Carbon Equivalent Control

There is no separate A134 chemistry table: the pipe is required to conform to the chemical limits of the plate specification used, checked either on the plate or on the finished pipe. A typical SA-516 Grade 70 analysis for plate up to 50 mm thick is carbon 0.28 % maximum, manganese 0.85–1.20 %, silicon 0.13–0.45 %, phosphorus 0.035 % maximum and sulphur 0.035 % maximum, with residual limits on copper, nickel, chromium and molybdenum. SA-285 Grade C is looser at the top end of carbon but carries lower manganese, which is why its strength is lower.

For welded construction the number that matters more than any single element is the carbon equivalent. A heat that meets every element limit can still crack in the seam if the carbon equivalent is at the top of the range and the heat input is low. Buyers specifying A134 pipe for restrained joints, thick walls or low ambient welding temperatures should therefore state a carbon equivalent limit calculated to a named formula and require the value on the mill certificate for each heat. This is standard practice in pressure piping and is the single most effective defence against delayed hydrogen cracking in the seam and in the girth welds made on site.

Two further points are frequently missed. Silicon and manganese are both raised in fully killed, fine-grain plate, and both increase weld metal dilution effects; a seam welded without matching filler metal can therefore finish harder than the plate. And because A134 permits repair welding of the seam, the repair procedure, the preheat and the post-weld treatment must be the same as those qualified for the original seam. A repair welded with a different consumable creates a local galvanic and toughness discontinuity that no mill test certificate will reveal.

Longitudinal and Helical Seam Welding

Straight-seam A134 pipe is produced by rolling a rectangular plate into a cylinder, tacking the longitudinal edges, and completing the seam by submerged arc welding from one or both sides. The plate edges are normally sheared or machined and then beveled; the bevel geometry, the root gap and the number of passes are part of the welding procedure qualification. After welding, the seam is inspected and the pipe is sized by mechanical expansion or by a sizing press to bring the roundness and the end squareness within tolerance.

Helical-seam pipe is formed by feeding plate continuously into a spiral forming head at a fixed forming angle, so the seam runs at an angle to the pipe axis. Diameter is controlled by the forming angle and plate width rather than by a fixed roll set, which makes the process flexible for large diameters but also means the seam length per metre of pipe is longer than for a straight seam. The consequence for inspection is important: a helical seam crosses the full circumference and cannot be radiographed with a single axial shot, so ultrasonic examination of the full seam length is the usual acceptance method, with radiography of a sample length as a cross-check.

Dimensions, Wall Thickness and Tolerances

A134 pipe is defined by outside diameter, nominal wall thickness, length and end finish. Because wall thickness equals plate thickness, the permissible minus tolerance on the wall follows the plate specification unless the purchase order tightens it. Purchasers who intend to calculate a design pressure should specify the minimum wall rather than the nominal wall, and should state whether the mill may supply plate at the minus tolerance in full. On large-diameter thin-wall pipe, out-of-roundness is the parameter that most often causes field fit-up problems: it is measured as the difference between the largest and the smallest outside diameter in a single cross-section, and it should be agreed as a percentage of nominal diameter.

Length is usually ordered as a fixed length with a small positive tolerance for cutting and beveling. End finishes are plain, beveled for welding, or specially machined for a flanged or a Victaulic-type coupling. Where the pipe will be girth welded on site, the end squareness and the bevel angle matter more than the length tolerance, because an out-of-square end forces a hi-lo misalignment that concentrates strain in the root pass.

Testing, Inspection and Documentation

A134 requires tensile testing to demonstrate that the pipe body meets the plate grade, and a hydrostatic test of each length or, when agreed between purchaser and manufacturer, non-destructive examination of the weld seam in place of hydrostatic testing. The hydrostatic test is not a formality: the test pressure is derived from a hoop-stress calculation using the specified minimum yield strength of the plate grade and the nominal wall, so a pipe made from a stronger grade is tested at a higher pressure than the same size in a weaker grade. Records of the test pressure, hold time and any leakage must be retained and traceable to the length number.

Weld quality is verified by radiographic or ultrasonic examination of the seam, with acceptance criteria agreed at the ordering stage. The two methods find different defects: radiography is sensitive to volumetric flaws such as porosity, slag and lack of penetration, while ultrasonic examination is better at planar flaws such as lack of fusion and at detecting them in thick walls. For helical seams and for walls above roughly 25 mm, ultrasonic examination with a documented procedure is the more reliable tool.

The document package a buyer should require is: an EN 10204 type 3.1 certificate referencing the plate heats and the pipe specification, the welding procedure specification and procedure qualification record, the welder and operator qualifications, the heat treatment record if any, the non-destructive examination reports with the technique and acceptance standard, the hydrostatic test record, and the dimensional inspection report. A certificate that lists only the pipe specification and a generic grade, without heat numbers, cannot be traced back to the plate and should be rejected.

Fabrication: Flanging, Bending and Field Welding

A134 pipe is intended to be fabricated. It can be cold flanged, hot formed, bent to a radius of several diameters, and welded to fittings without losing the properties reported on the certificate, provided the fabrication procedure respects the plate grade. Two rules govern most of the risk. Cold bending beyond a modest strain level in a grade with a high carbon equivalent should be followed by a stress-relief heat treatment; and any hot forming that exceeds the tempering or normalizing temperature of the plate destroys the supplied condition and requires re-heat-treatment of the affected zone.

Field girth welding of A134 pipe is usually the point where good pipe becomes a poor line. The mismatches that cause trouble are hydrogen (damp electrodes, no preheat on thick wall), restraint (short pups between anchors), and dilution (a low-strength cellulosic root on a Grade 70 plate). All three are controlled by the welding procedure, not by the pipe. Requiring the contractor to work to a qualified procedure with preheat matched to wall thickness and carbon equivalent is worth more than buying the next grade up.

Where A134 Pipe Fits in a Specification

Typical applications are plant piping in refineries and chemical works where size and wall thickness rule out seamless tube, large-diameter water and slurry lines, penstock and cooling-water piping, structural and piling service at large diameter, and pressure piping designed to ASME B31.3 or to Section VIII rules where a plate-based welded pipe is permitted. In each case the selection logic is the same: choose the plate grade from the operating temperature and toughness requirement, choose the wall from the design pressure and corrosion allowance, choose straight or helical seam from the diameter and the inspection method available, and then write the inspection and documentation requirements into the order.

Where the service is sour, or where the pipe will carry wet gas containing hydrogen sulphide, A134 is not the right answer regardless of grade: the plate grades covered by the specification are not qualified to the hardness and chemistry controls required for sour service, and a pipe that passes a hydrostatic test can still fail by sulphide stress cracking in service. In such cases a specification written for sour service, with hardness testing of the seam and heat-affected zone, must be used.

FAQ

Q: Is ASTM A134 pipe the same as ASME SA134 pipe?
Yes. The two designations describe the same specification; ASME SA134 appears in Section II Part A of the Boiler and Pressure Vessel Code and is technically identical, with the ASME version being the one referenced in code construction. A certificate to either designation should be accepted when the project code allows the specification.

Q: Can A134 pipe be used for high-pressure gas service?
Only when the design code used by the project permits electric-fusion-welded pipe and when the wall, the plate grade and the weld examination have been specified accordingly. Transmission pipeline service normally calls for API 5L product with defined toughness and weld quality, because A134 imposes no pipe-body impact requirement and no automatic full-seam radiographic acceptance.

Q: Why does the wall thickness tolerance differ from a seamless pipe?
Because the wall is a plate thickness. The tolerance is taken from the plate specification, and plate is rolled to a thickness tolerance that is expressed differently from pipe wall tolerance. Buyers converting a seamless design to A134 must re-check the minimum wall, not only the nominal wall.

Q: What plate grade should be specified for low-temperature service?
SA-516 in the strength grade required by the design, ordered with a Charpy impact test supplement at the minimum design metal temperature. SA-515 is intended for elevated temperature service and SA-285 has no toughness guarantee, so neither should be substituted for SA-516 on cold duty.

Q: Does A134 specify a carbon equivalent limit?
The specification relies on the chemistry limits of the plate grade. Carbon equivalent limits, hardness limits and weldability requirements are purchaser options and must be written into the purchase order, with the calculation formula and the maximum permitted value stated explicitly.

Q: How is the seam examined on helical-seam pipe?
Ultrasonic examination along the full seam length is the practical method, because the seam crosses the circumference at an angle and cannot be covered by a single axial radiograph. Radiography of a sample length is normally added as a cross-check, and the acceptance criteria should be agreed before the order is placed.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry