What Electric Resistance Welding Actually Does to the Strip
ERW line pipe starts as hot rolled coil that is uncoiled, slitted to width, edge-trimmed and progressively formed through a series of rolls into a cylinder. The two longitudinal edges are then brought together under pressure while a high-frequency current, usually in the range of 100 kHz to 450 kHz, is fed through them by induction coils or sliding contacts. The current concentrates in the edge skin and the contact resistance at the vee apex, the metal reaches a forging temperature without melting the full section, and squeeze rolls consolidate the joint. No filler metal is added, so the seam chemistry is essentially the parent strip chemistry and the mechanical properties of the weld follow the thermal cycle it has seen.
That physics explains both the strengths and the limits of the product. Because the weld is forged rather than cast, an ERW seam has no cast dendritic structure and usually shows good toughness after seam heat treatment, along with dimensional accuracy from a continuous forming line and a cost base lower than a seamless mill. The corresponding weaknesses are geometrical: the seam is a narrow bond whose quality depends on edge preparation, vee alignment and squeeze force, so it can carry lack of fusion, cold welds, oxides or a hook crack that a simple visual inspection will not reveal. That is why every serious specification buys ERW pipe with a weld seam inspection requirement attached, and why the mill's inspection record matters as much as the chemical certificate.
Grades and Product Specification Levels Available in ERW
API 5L ERW pipe is supplied in PSL1 and PSL2. Grades A and B are the baseline carbon steel grades; X42, X46, X52, X56, X60, X65 and X70 cover the higher yield levels used in transmission and gathering lines. PSL1 is the quality level intended for ordinary service, with looser chemistry limits and no mandatory toughness testing. PSL2 adds tighter phosphorus and sulphur limits, a carbon equivalent or Pcm ceiling, mandatory tensile and impact testing, mandatory non-destructive inspection of the weld seam, and a requirement that all tests be traceable to the pipe and to the heat. A purchase order that says only \"API 5L X52\" leaves the specification level open, and that single omission changes the inspection scope, the documentation and the delivered price of the order.
Practical ERW production covers outside diameters from roughly 21.3 mm to 660 mm and wall thickness from about 2.0 mm to 20 mm, with the exact capability of a given mill set by its forming rolls, its welder power and its sizing stands. Above roughly 16 mm wall and above 20 inches diameter, the economics shift toward LSAW and seamless, so an enquiry for ERW at 24 inch with 20 mm wall should expect either a technical exception or a proposal in a different process.
Chemistry Limits That Separate PSL1 from PSL2
Chemistry control in ERW pipe serves two purposes: it delivers the required yield and tensile strength through manganese and microalloying, and it keeps carbon equivalent low enough for field weldability. The table below gives the limits that dominate the purchase decision.
| Element or index | PSL1 welded pipe | PSL2 welded pipe | Effect on the buyer |
|---|---|---|---|
| Carbon, maximum | 0.26 % for grade B and X grades | 0.22 % for grade B and higher | Lower carbon improves field weldability and heat affected zone toughness |
| Manganese, maximum | 1.20 % grade B, up to 1.65 % for X70 | 1.20 % grade B, up to 1.85 % for X70 | Raises strength, raises carbon equivalent |
| Phosphorus, maximum | 0.030 % | 0.025 % | Lower phosphorus reduces segregation and brittle fracture risk |
| Sulphur, maximum | 0.030 % | 0.015 % | Lower sulphur improves toughness and weldability, especially in the seam |
| Carbon equivalent, IIW | Not specified | 0.43 maximum for X42 and above | Directly controls preheat and hydrogen management on site |
| Pcm | Not specified | 0.25 maximum for X52 and above, carbon at or below 0.12 % | Alternative weldability index for low-carbon microalloyed designs |
Mechanical Properties by Grade
Yield and tensile requirements for PSL2 pipe body are stated as ranges rather than single minimums, and the upper limits matter as much as the lower ones when a line is designed for strain based loading or for compatibility with a specific welding procedure.
| Grade | Yield strength, MPa | Tensile strength, MPa | Typical service |
|---|---|---|---|
| B | 241 to 448 | 414 to 758 | Water, slurry, low pressure utility lines |
| X42 | 290 to 496 | 414 to 758 | Low pressure gathering and distribution |
| X46 | 317 to 524 | 434 to 758 | Medium pressure gathering lines |
| X52 | 359 to 530 | 455 to 760 | General transmission, station piping |
| X56 | 386 to 544 | 490 to 760 | Transmission with moderate pressure |
| X60 | 414 to 565 | 517 to 760 | Mainline transmission |
| X65 | 448 to 600 | 535 to 760 | High pressure mainline |
| X70 | 483 to 621 | 565 to 758 | High pressure, large diameter transmission |
The Seam: Heat Treatment, Defect Morphology and Inspection
After welding and before sizing, the seam passes an in-line induction or gas heat treatment station. Normalising the seam raises the weld zone to a temperature close to 900 degrees C and above, and air cooling then refines the grain structure and removes the hard, coarse zone created by the forging thermal cycle. Without that step, a high-frequency weld in a microalloyed strip can show hardness well above the parent metal and toughness well below it, and the seam becomes the weak link in a fracture propagation assessment. Purchasers should ask whether the seam is normalised, only stress relieved, or untreated, because the three conditions are not interchangeable and are not visible in the finished pipe.
Defect morphology in an ERW seam is distinctive. Lack of fusion appears as an unbonded interface, often with oxide stringers, and may be planar and tight, which is difficult to size. A stitch or penetrator is a short unbonded segment that can pass a coarse test and fail under pressure cycling. A hook crack is a small crack at the bond line caused by excessive heat input or poor edge condition, curving into the wall. A cold weld shows adequate geometry with inadequate bonding. Because these are planar and narrow, radiography is a poor primary tool for the ERW seam; automatic ultrasonic testing of the weld seam, performed in line with a phased array or a focused shear wave probe arrangement, is the standard method, with the technique and reference notch requirements set by ISO 10893-11 and by API SPEC 5L Annex E where the purchase order invokes it.
Dimensions, Tolerances and End Finishes
ERW pipe holds diameter tolerance to about plus or minus 0.75 percent of outside diameter for the range from 60.3 mm to 610 mm, with tighter fixed limits for small sizes, and wall thickness tolerance for welded pipe is stated as a percentage of nominal wall in the middle thickness band rather than a single fixed figure. Straightness, length tolerance, end squareness and the bevel angle all matter at the tie-in: an out-of-square end forces a wider root gap, which changes the welding procedure that the contractor qualified.
Pipe ends are supplied plain, bevelled or threaded. Bevelled ends are cut to 30 degrees plus or minus 2.5 degrees with a root face around 1.6 mm on standard wall. Threaded and coupled pipe for API 5CT casing or for API 5B line pipe connections requires thread gauging and coupling make-up records. Coating options include bare, black lacquered, fusion bonded epoxy, three layer polyethylene, and hot dip galvanised for the smaller sizes used in structural and utility service, and each coating changes handling requirements rather than the pipe itself.
Testing Routine and Documentation for a Purchased Lot
A PSL2 ERW order should arrive with tensile tests on the pipe body and on the weld, flattening tests on a ring cut from each test unit, a weld seam tensile test, Charpy impact tests on the pipe body and the seam where toughness is specified, a hydrostatic test at the pressure calculated under API SPEC 5L, and non-destructive inspection of the full seam length. Hydrostatic holding time under API SPEC 5L is 5 seconds for pipe below 508 mm diameter and 10 seconds at or above that size, and the test pressure is capped so that hoop stress does not exceed the limit set for the grade, which is why a request for a very high test pressure on thin wall cannot physically be met. Dimensional inspection covers diameter, wall, length, straightness and bevel.
Documentation is part of the product. An inspection certificate to EN 10204 3.1 type, linking heat number to pipe number, is the normal basis for PSL2. The buyer should verify that the grade, specification level, outside diameter, wall thickness and heat number on the certificate match the markings on the pipe and the packing list, and that the impact test temperature corresponds to the service requirement rather than to a default room temperature result.
Choosing ERW Against Seamless or Submerged Arc Pipe
ERW is normally the most economical choice for diameters from about 2 inch to 24 inch in moderate wall thickness, especially where dimensional accuracy, concentricity and a smooth inside surface matter for pigging or for liners. Seamless pipe is preferred where the wall is heavy relative to the diameter, where the service involves high collapse or axial loading, and where a purchaser wants to avoid a longitudinal weld entirely, as in some sour service and high pressure downhole applications. LSAW takes over at large diameter with heavy wall, where a formed plate and a double sided submerged arc weld give better toughness control than a single pass forge weld at that thickness. SSAW suits very large diameter, moderate pressure lines where cost per metre dominates.
The decision should also weigh the inspection burden. A seamless pipe carries no seam inspection requirement because it has no seam, whereas an ERW order should always specify the seam inspection technique and the acceptance level, and should state whether repair of the seam by welding is permitted at all. Many specifications refuse weld repairs on the seam and require cut-back instead, which is a cleaner rule than trying to qualify a repair procedure for a forged bond line.
FAQ
Q: Is ERW pipe weaker than seamless pipe of the same grade?
Not in the pipe body. The specified yield and tensile ranges are the same for a given grade, and PSL2 requires the same tensile testing. The difference lies in the weld seam, which is a forged bond with its own inspection requirements and its own susceptibility to planar defects, so the seam quality record rather than the grade determines whether the pipe performs as intended.
Q: What does PSL2 add over PSL1 for ERW pipe?
Tighter phosphorus and sulphur limits at 0.025 percent and 0.015 percent, a carbon ceiling of 0.22 percent, carbon equivalent and Pcm limits, mandatory non-destructive inspection of the weld seam, mandatory tensile and impact testing, and full traceability of results to heat and pipe.
Q: Why is ultrasonic testing preferred over radiography on the ERW seam?
Seam defects such as lack of fusion, cold welds and hook cracks are tight and planar, and their plane is unfavourable for radiographic detection. Focused shear wave or phased array ultrasonic testing aimed at the bond line detects and sizes these indications far more reliably, which is why ISO 10893-11 and API SPEC 5L Annex E define ultrasonic techniques for the weld seam.
Q: Does ERW pipe require seam heat treatment?
Seam heat treatment is not universal, but normalising of the seam is specified for grades and wall thickness where the as-welded zone would otherwise show excessive hardness and poor toughness. Stress relieving only reduces residual stress and does not refine the grain structure, so the two treatments should not be treated as equivalents in a specification.
Q: What diameter and wall range is realistic for ERW line pipe?
Common production runs from about 21.3 mm to 660 mm outside diameter and 2.0 mm to 20 mm wall. Beyond roughly 16 mm wall and 20 inches diameter the process competes poorly with LSAW and seamless, so a technical review is warranted before a large enquiry is placed on ERW.
Q: How should the hydrostatic test be specified?
Specify the test pressure through the hoop stress calculation in API SPEC 5L rather than an arbitrary figure, and state the holding time, which is 5 seconds below 508 mm diameter and 10 seconds at or above it. The standard also caps the hoop stress, so an unrealistic pressure demand on thin wall will simply be rejected at the technical review stage.






