What Hot-Dip Galvanising Does to a Steel Pipe
Galvanising is the application of a zinc coating to steel, and the coating protects the steel in two different ways at once. As a barrier it seals the surface from moisture and oxygen. As a sacrificial anode it corrodes in preference to the steel at scratches, cut ends and damaged threads, because zinc is less noble than iron. That second mechanism is what separates galvanising from paint: a painted coating fails from the first pinhole outward, while a zinc coating keeps protecting a small exposed area until the surrounding zinc is consumed.
The process used for pipe is hot-dip galvanising. The tube is degreased, pickled, fluxed and then immersed in molten zinc at approximately 445 to 465 degrees Celsius, as specified in ISO 1461 and in ASTM A123/A123M. The result is a metallurgically bonded coating built from a sequence of zinc-iron alloy layers, from the eta layer of nearly pure zinc at the outer surface through the zeta, delta and gamma layers to the steel interface. The alloy layers are hard and moderately brittle, which explains why galvanised pipe is handled with care at cut edges and why very thick coatings are not automatically better on parts that will be bent or threaded.
Coating Mass, Thickness and the Standards That Set Them
Coating thickness is the single best predictor of galvanised pipe life, and it is controlled by two things: the zinc mass applied per unit area and the silicon and phosphorus content of the base steel, which affects the reaction rate in the bath. Reporting practice differs between markets. Coating mass is stated in grams per square metre, and the conversion is fixed by the density of zinc, roughly 7.14 grams per cubic centimetre, so 1 micrometre of coating equals about 7.1 grams per square metre. A coating of 300 grams per square metre therefore measures about 42 micrometres and a coating of 600 grams per square metre about 84 micrometres.
| Standard | Scope | Coating requirement pattern | Test method |
|---|---|---|---|
| ASTM A123/A123M | Zinc coating on iron and steel products | Minimum average thickness rising from about 45 to 85 micrometres with base metal thickness | Coating mass by ASTM A90/A90M, magnetic gauge per ASTM E376 |
| ISO 1461 | Hot-dip galvanised coatings on fabricated iron and steel | Local and average thickness bands from about 55 to 85 micrometres depending on steel thickness | Gravimetric and magnetic methods, reference areas defined |
| ASTM A53/A53M | Galvanised welded and seamless pipe | Minimum coating stated by the pipe standard, heavier coating by agreement | Coating mass and thickness, plus hydrostatic test |
| ASTM A153/A153M | Zinc coating on hardware and threaded fittings | Class-based coating mass for threaded components | Gravimetric, with thread allowance rules |
| EN 10240 | Internal and external coatings on welded steel tube | Coating classes by mass per unit area, internal and external declared separately | Gravimetric on defined test pieces |
Two acceptance habits follow from this table. First, the coating requirement must be quoted with its test basis, because a gravimetric result on a dissolved sample and a magnetic gauge reading on a curved surface do not agree to the last micrometre, and disputes at inspection usually come from mixing the two. Second, external and internal coatings are separate requirements on pipe. A pipe with a heavy external coating and a nominal internal coating will corrode from the bore in water service, and the order should state the internal coating mass explicitly.
Corrosion Rate by Environment and How to Estimate Service Life
Zinc corrodes at a rate set by the environment, and the rate is well characterised by the corrosivity categories of ISO 9223 and ISO 12944, which publish first-year zinc mass loss bands for atmosphere types. Combining a measured coating thickness with the category rate gives a defensible life estimate, and that estimate is far more useful than a single generic number quoted in a catalogue.
| Corrosivity category | Typical environment | Zinc corrosion rate (micrometres per year) | Indicative life at 85 micrometres |
|---|---|---|---|
| C1 | Heated, dry interior | 0.1 or less | Well over 50 years |
| C2 | Rural, low pollution, unheated interior | 0.1 to 0.7 | About 50 years and beyond |
| C3 | Urban, industrial with moderate sulphur dioxide | 0.7 to 2.1 | Roughly 40 to 120 years |
| C4 | Industrial, coastal with moderate salinity | 2.1 to 4.2 | Roughly 20 to 40 years |
| C5 | Heavy industrial or high salinity coastal | 4.2 to 8.4 | Roughly 10 to 20 years |
| CX | Extreme industrial or offshore | 8.4 to 25 | Roughly 3 to 10 years |
Buried service is a special case. Zinc in soil depends on resistivity, pH, chloride and the presence of stray current, and the coating alone is rarely the design basis for a buried line: heavier coating plus wrapping, or coating plus cathodic protection, is the normal combination. Where the pipe is to be coated after galvanising, the two systems must be compatible, because a zinc surface that has been passivated or painted over can prevent the outer coating from bonding.
Pipe Standards, Base Metal and Delivery Condition
Galvanised pipe is ordered to a pipe standard that defines the steel, the dimensions and the pressure test, with galvanising added as a coating requirement to a separate standard. ASTM A53/A53M covers welded and seamless black and hot-dipped galvanised pipe in Grades A and B, with Type F continuous welded, Type E electric resistance welded and Type S seamless, and dimensions referenced to ASME B36.10M. Welded galvanised pipe to GB/T 3091 is widely ordered in water and construction duty, with coating mass commonly specified at 300 grams per square metre or higher. The steel grade and the pipe standard are not interchangeable with an arbitrary tube specification, because the pressure rating and the wall tolerance belong to the pipe standard, not to the coating standard.
One detail in A53 is often missed: pipe intended for galvanising must be suitable for the process, and the standard addresses the weld condition and the surface preparation before coating. A heavily oiled or rusted surface will produce a coating with poor adhesion or with thick, brittle zinc-iron layers, and neither defect will be visible in a photograph. Purchasers should require the mill certificate to state the coating mass achieved, together with the pipe standard, grade and heat number, on an EN 10204 3.1 document.
Threading, Cutting and Joining Without Losing the Coating
Galvanised pipe is normally jointed with threaded fittings because threading is fast, demountable and does not burn the coating over a wide area. Threads are cut to the taper and thread form of ASTM B1.20.1, and threading inevitably removes the coating from the thread surface, which is why the specification approach is to protect the exposed thread with an approved joint compound and to rely on zinc-coated fittings to ASTM A153/A153M rather than on bare fittings.
Welding is possible but changes the corrosion situation. The zinc is burned away beside the weld, leaving a bare band that must be recoated, and zinc oxide fume generated during welding requires extraction and respiratory protection under the applicable occupational exposure rules; the process should therefore be planned as a controlled repair operation rather than treated as ordinary pipe welding. All cut ends, damaged areas and weld-affected zones need repair with a zinc-rich coating, and repair practice is covered by ASTM A780. A repair that is applied over rust or over a poorly cleaned surface will fail within a season, so surface preparation before repair is part of the acceptance criterion.
Bending galvanised pipe is possible for moderate radii, but a thick, brittle coating will craze on the outside of the bend and expose steel. Where bends are part of the design, the order should specify the bending radius, or the pipe should be bent before galvanising. Cold working of heavily galvanised steel also raises the question of strain-age embrittlement, and ASTM A143 sets out safeguards to be agreed where cold forming and galvanising are combined.
White Rust, Storage and In-Service Water Chemistry
White rust is the pale, powdery zinc hydroxide and zinc carbonate product that forms when freshly galvanised surfaces are stored in damp, poorly ventilated conditions and the protective oxide film cannot develop. It is a storage and transport defect, not a corrosion failure, but it consumes coating and it is a common reason for rejection at goods receipt. Prevention is procedural: keep the bundles off the ground, space them so air moves between pipes, avoid condensation cycles in a container, and require either adequate drying before packing or a passivation treatment agreed at the time of order.
In water service the coating is also sensitive to the water itself. Zinc passivates and performs well in the near-neutral pH range, roughly 6 to 12, and it corrodes quickly in soft, acidic water with low alkalinity. Waters with high chloride content, high dissolved oxygen and elevated temperature increase the zinc dissolution rate, and the first weeks of service are when most of the protective film forms, so commissioning should avoid long stagnation. Galvanised pipe is also cathodic to copper and to most brasses, so direct connection to copper components promotes corrosion of the zinc at the joint; a dielectric coupling at the transition is standard practice. Suitability for potable water depends on the local water quality rules and on the limits for zinc and any residual lead or cadmium in the coating, which must be confirmed against the applicable drinking water regulation before the pipe is released to that duty.
Inspection, Sampling and Document Acceptance
Acceptance of a galvanised pipe lot rests on three checks that are simple enough to perform at goods receipt. The first is coating mass or thickness, measured on defined reference areas by the gravimetric method of ASTM A90/A90M or by magnetic gauge per ASTM E376, with a stated number of readings per length and a stated minimum average and minimum individual value. The second is appearance and continuity: the surface must be continuous, free of bare spots, blisters, lumps and excessive zinc ash, and thread areas must carry their specified coating with the thread profile still within tolerance after coating. The third is dimensional and pressure integrity, checked against the pipe standard through the hydrostatic test record or the nondestructive test route the standard permits.
The documents should allow the pipe on site to be tied to the test results. That means an EN 10204 3.1 certificate showing the pipe standard, grade, size, heat number and coating result, and marking on the pipe or bundle that carries the same identifiers. Where a third party inspection is required, the inspection release should be issued against the actual test report rather than against a generic declaration of conformity.
Specification Mistakes Worth Avoiding
Most galvanised pipe complaints trace back to an incomplete purchase order. The recurring ones are: quoting a coating thickness without a test method or a sampling plan, so the result cannot be disputed or defended; specifying only external coating and leaving the bore to the mill; ordering A53 pipe but accepting a tube standard with different wall tolerance; buying galvanised pipe for a duty above the environmental category the coating can support, such as direct burial without wrapping; and accepting thread cutting after galvanising without a repair procedure for the exposed thread. Each of these is settled by one or two additional lines in the enquiry, and none of them can be fixed after the pipe is installed.
FAQ
Q: How thick should the zinc coating be on galvanised steel pipe?
For general atmospheric service, an average coating of about 55 to 85 micrometres is typical under ISO 1461 and ASTM A123/A123M, equivalent to roughly 390 to 600 grams per square metre. Thicker coatings are specified for coastal, industrial or buried duty, where the corrosion rate is higher.
Q: How long does galvanised steel pipe last?
Life depends mainly on the environment. Expect 50 years or more in dry indoor service, 20 to 40 years in coastal or industrial atmospheres at 85 micrometres, and about 10 to 20 years in high salinity or heavy industrial conditions. Buried service usually needs a heavier coating with wrapping or cathodic protection.
Q: Can galvanised pipe be welded?
It can, but the zinc must be removed from the joint area, fume extraction is required because zinc oxide fume is hazardous, and the weld and heat affected zone must be recoated with a zinc-rich product to ASTM A780. Threaded joints are preferred where the design allows.
Q: What is white rust and is it a defect?
White rust is zinc hydroxide and zinc carbonate formed by condensation on freshly galvanised surfaces in damp, unventilated storage. It consumes coating and is a legitimate rejection point, but it is a storage condition rather than a coating process failure, and it is prevented by ventilation, drying and passivation.
Q: Why does galvanised pipe corrode at connections to brass or copper fittings?
Zinc is anodic to copper alloys, so a galvanic couple forms at the transition and the zinc coating corrodes preferentially. A dielectric union or a coated isolating connection at the transition is the usual remedy.
Q: Which standards apply to galvanised steel pipe?
The pipe itself to ASTM A53/A53M or GB/T 3091 with dimensions per ASME B36.10M, the coating to ASTM A123/A123M, ISO 1461 or EN 10240, coated threaded fittings to ASTM A153/A153M, threads to ASTM B1.20.1, and damaged area repair to ASTM A780.





