Oct 29, 2024 Leave a message

Offshore Pipeline Corrosion Protection: Coatings, CP and Alloys

Three Corrosion Load Cases Acting on One Subsea Line

An offshore pipeline is attacked from three directions at once, and each attack needs a different defence. Seawater attacks the external surface at a rate governed by dissolved oxygen, temperature, flow velocity and the presence of sulphate reducing bacteria in sediment; the transported fluid attacks the internal surface through carbon dioxide, hydrogen sulphide, organic acids and free water; and the splash zone plus the riser transition adds mechanical damage, ultraviolet exposure and cyclic loading on top of both. A corrosion protection scheme that addresses only one of these cases will fail inside the design life even if the coating itself performs perfectly.

The governing documents are usually DNV-ST-F101 for the pipeline system, API RP 1111 for design and operation, ISO 21809 for the external coating, ISO 15589-2 for offshore cathodic protection and ISO 15156 together with NACE MR0175 when hydrogen sulphide is present. A purchase specification that cites only API SPEC 5L covers the pipe as a pressure vessel and says almost nothing about corrosion protection, which is why line pipe for subsea service is normally ordered with a coating annex, a cathodic protection design report and a material selection report attached.

External Coatings: What Each System Is Good At

Fusion bonded epoxy to ISO 21809-2 remains the default for high temperature and for pipe that will be concrete weight coated, because a thin 300 to 500 micrometre film bonds chemically to a blast cleaned surface, tolerates operating temperatures up to about 100 degrees Celsius for standard grades and resists abrasion during installation. Its weakness is mechanical damage tolerance and its sensitivity to surface preparation: a blast profile outside about 40 to 100 micrometres, residual salt contamination above a low threshold, or a cure that is too fast will produce disbondment that only shows up as a cathodic protection current demand years later.

Three layer polyethylene to ISO 21809-1 and three layer polypropylene add a thick mechanical barrier over the epoxy primer. A typical 3LPE build on a 610 mm line pipe is 2.5 to 4.0 mm total, of which the epoxy primer is 80 to 150 micrometres, the copolymer adhesive 150 to 300 micrometres and the polyethylene topcoat carries the rest. 3LPP uses a polypropylene topcoat where operating temperature exceeds the polyethylene softening range, typically above 70 to 80 degrees Celsius, at the cost of slightly lower flexibility and higher installation damage sensitivity. Coal tar enamel and asphalt enamel, both still found on legacy lines, offer excellent water resistance but are being phased out on environmental and personnel exposure grounds; repair and compatibility strategy rather than new installation is the normal reason to reference them today.

Concrete Weight Coating and Mechanical Protection

Negative buoyancy and mechanical protection are usually delivered by an external concrete weight coating applied over the corrosion coating, with density typically between 2,240 and 3,045 kilograms per cubic metre depending on whether hematite or iron ore aggregate is used, and thickness generally between 40 and 150 mm. The coating must be reinforced with steel mesh, and it must be designed so that it does not crack through to the corrosion coating during laying: impact resistance, shear resistance at the concrete to coating interface and water absorption are the properties that matter, not only compressive strength.

ISO 21809-5 covers the application of external concrete coatings, and it should be read with the installation method in mind. S-lay imposes high curvature over the stinger, J-lay imposes concentrated loads at the tensioner and the aligner, and reel lay imposes the most severe combination. A weight coating accepted against a static compressive strength figure alone frequently cracks on a reel lay vessel, at which point seawater reaches the corrosion coating and the cathodic protection current demand rises beyond the anodes that were sized for an intact coating.

Field Joint Coatings: The Weakest Link

Between 2 and 5 percent of the external surface of a completed pipeline is field joint, and that small area accounts for a disproportionate share of corrosion failures. Girth welds are coated in the field with a heat shrink sleeve, a flame sprayed or epoxy based system, or an injection moulded polyurethane collar, all covered by ISO 21809-3. The critical requirements are that the cut back length be controlled so that the parent coating is not overheated during welding, that surface preparation at the joint match the mill applied interface, and that the joint coating be tested for indentation and impact at the laying temperature rather than at ambient.

Where the line will be operated above 60 degrees Celsius, the field joint system must be qualified for the same temperature as the parent coating, and a compatible transition, sometimes a graded taper rather than a square cut, is required to prevent a stress concentration that peels the sleeve edge. Compatibility between mill coating and field joint material should be proven by a peel test on production pipe, not accepted on the supplier's generic data sheet.

Sacrificial Anode Cathodic Protection Design

Cathodic protection is not a substitute for coating; it is the backup that keeps the steel polarised at coating holidays and at damage sustained during installation. Subsea systems are almost always galvanic, using aluminium-zinc-indium or zinc alloy anodes qualified by composition and electrochemical testing such as ASTM G97 for aluminium anodes. The anode mass and current output are calculated from the wetted surface area, the design current density for the relevant seawater zone, the coating breakdown factor over the design life, and the electrochemical capacity and closed circuit potential of the anode alloy.

Design current densities are temperature and depth dependent, and DNV-RP-B401 provides the tabulated values that most designs start from; for a well coated pipe in cold deep water the initial current density can be an order of magnitude lower than for bare steel in warm shallow water. Anode spacing is a hydraulic and electrical question as much as a mechanical one: on a coated line the practice is to keep the spacing between anodes at or below about 150 metres so that the potential at the mid span stays inside the protection criterion, and the calculation should demonstrate the potential profile, not just the total mass. Anode blocks are normally half shells welded to the pipe with a copper or aluminium connecting strap, and the weld must be qualified so that it does not embrittle or dent the line pipe, particularly on thin wall high grade pipe.

Protection Criteria and the Overprotection Trap

The conventional acceptance criterion for steel in seawater is a potential of minus 0.80 volts or more negative measured against a silver-silver chloride seawater reference electrode, with the alternative 100 millivolt polarisation decay criterion accepted in some codes. The upper bound matters as much as the lower: potentials more negative than about minus 1.05 volts on high strength or duplex steel risk hydrogen induced cracking, and DNV-RP-F112 addresses exactly that interaction for duplex stainless steel under cathodic protection. A protection design that simply maximises anode mass to be "safe" can therefore create a hydrogen cracking problem where none existed.

Measurement is part of the design. Retrofit or pre-installed monitoring arrangements, either galvanic potential probes at the pipe ends or remote operated vehicle surveys with a calibrated half cell, should be specified so that the operator can verify the criterion during the design life rather than infer it from the anode consumption model. The as-laid survey, taken shortly after installation, is the baseline against which every later inspection is compared.

Internal Corrosion Control Options

Internal corrosion control is decided by the produced fluid, not by preference. The essential inputs are the oil, gas and water ratio, the water salinity and pH, the carbon dioxide and hydrogen sulphide partial pressures, the bacterial population, the solids content and the flow regime, and the operating temperature and pressure profile from wellhead to host. From those, a corrosion assessment predicts the uninhibited corrosion rate and the resulting corrosion allowance, which is commonly in the range of 1.5 to 3 mm for carbon steel lines but must be calculated rather than assumed.

Where the allowance is uneconomic or the predicted rate is unacceptable, the options are: continuous or batch injection of a filmed amine based corrosion inhibitor with the dose verified by a flow loop or rotating cylinder test; internal flowline coating, typically a solvent free epoxy of 250 to 400 micrometres; corrosion resistant alloy pipe or clad pipe to API 5LD, for example a metallurgically bonded Alloy 625 (UNS N06625) liner in a carbon steel carrier; or simply keeping the line dry by controlling dew point and pigging to remove water accumulation at low points. Inhibitor selection must be compatible with the fluid and with the host facility's separation chemistry, because an over-dosed or incompatible product can stabilise emulsions and create an operational problem worse than the corrosion it prevented.

Material Selection When Hydrogen Sulphide Is Present

Sour service changes the rules entirely. ISO 15156 and NACE MR0175 govern carbon steel, low alloy steel and corrosion resistant alloys in hydrogen sulphide containing environments, using the partial pressure of hydrogen sulphide together with in situ pH and the presence of elemental sulphur to define service regions, with 0.3 kilopascals of hydrogen sulphide partial pressure as the widely applied entry threshold. Carbon steel in sour service is normally required to meet a hardness cap of 250 HV10 in the pipe body, weld and heat affected zone, to be supplied in a normalised or quenched and tempered condition, and to be qualified by a materials and welding procedure that includes sulphide stress cracking testing to NACE TM0177 and, where relevant, hydrogen induced cracking testing to NACE TM0284.

For high collapse resistance and for deepwater installation, the interaction between sour service and cathodic protection must be assessed as one problem. A line that is sour internally and cathodically protected externally at minus 1.0 volt is charged with hydrogen from the outside while being embrittled from the inside, and the hardness and microstructure requirements have to be met on both counts. This is one of the few areas where a buyer should insist on a single materials engineering report covering pipe, weld, coating and cathodic protection together rather than three separate annexes from three suppliers.

Coating System Comparison

System Typical thickness Service temperature Main strength Main risk Standard
Fusion bonded epoxy 300 to 500 micrometres up to about 100 degrees Celsius Adhesion, high temperature, low CP shielding Mechanical damage, surface preparation sensitivity ISO 21809-2
Three layer polyethylene 2.5 to 4.0 mm total up to about 70 degrees Celsius Mechanical toughness, low water permeation Disbondment at high temperature, shielding of CP if damaged ISO 21809-1
Three layer polypropylene 2.6 to 4.5 mm total up to about 110 degrees Celsius Higher temperature service Lower flexibility, installation damage ISO 21809-1
Concrete weight coating 40 to 150 mm not a barrier coating Negative buoyancy, impact protection Cracking during laying, mesh corrosion ISO 21809-5
Heat shrink sleeve field joint 2.0 to 3.5 mm matched to parent coating Fast field application Edge peel, inadequate surface preparation ISO 21809-3
Internal epoxy lining 250 to 400 micrometres up to about 90 degrees Celsius Reduces inhibitor demand, lowers friction Holiday at girth weld, blistering ISO 21809-3, API RP 5L2

Thickness values above are commercial ranges for line pipe rather than fixed requirements; the purchase order should state the class and grade of coating from the relevant ISO 21809 part, and the qualification test temperature should equal or exceed the maximum operating temperature plus a design margin agreed with the operator.

What to Verify Before the Pipe Leaves the Yard

Coating inspection should be performed to a written inspection and test plan that covers surface profile and salt contamination before application, coating thickness at defined measurement points, holiday detection at a voltage appropriate to the coating thickness, adhesion by peel or pull off test, and cathodic disbondment at the design temperature. Impact and indentation resistance at the installation temperature are the tests most often omitted and most often responsible for in service failures.

For the pipe itself, the documentation should include the mill test certificate to EN 10204 type 3.1, the weld procedure qualification records, dimensional records including out of roundness at the ends because girth welding on an oval pipe produces high low stress, and hydrostatic test records. A single package containing pipe, coating, anodes and field joint procedure, cross referenced to DNV-ST-F101 and the project's material selection report, is what allows an operator to demonstrate fitness for service later, when the questions being asked are about remaining life rather than about delivery.

Common Misconceptions

One persistent error is treating cathodic protection as a complete barrier. It protects exposed steel at holidays but cannot penetrate a disbonded coating that has formed a shielding pocket, and it cannot protect a surface that is electrically screened by a concrete weight coating that has cracked and filled with sediment. A second is assuming that a thicker coating is always better: above a certain thickness, polyethylene and polypropylene coatings lose flexibility and increase the risk of cathodic protection shielding at damage sites, which is why thickness is capped in the ISO 21809 classes. A third is sizing anodes by total mass only and ignoring current distribution, which produces a design that satisfies the arithmetic and fails the potential survey at mid span.

FAQ

Q: Can a three layer polyethylene coating be used at 90 degrees Celsius operating temperature?
Not with standard polyethylene grades. Above roughly 70 to 80 degrees Celsius the polyethylene softens and the adhesive bond degrades, so a polypropylene based three layer system or a high temperature epoxy is required, with cathodic disbondment testing at the design temperature.

Q: What cathodic protection potential should be specified for a carbon steel subsea line?
Minus 0.80 volts against a silver-silver chloride seawater reference is the usual protection criterion, with the negative limit capped near minus 1.05 volts to avoid hydrogen damage on high strength steels. The 100 millivolt polarisation decay criterion is an accepted alternative where the design code permits it.

Q: How is the corrosion allowance decided for a wet gas line?
From a corrosion assessment using carbon dioxide and hydrogen sulphide partial pressures, water chemistry, temperature and flow regime, which predicts an uninhibited corrosion rate; the allowance is then the predicted rate multiplied by the design life, reduced by the demonstrated effectiveness of inhibition.

Q: When is clad pipe cheaper than increasing the corrosion allowance?
When the predicted corrosion rate is high enough that the required allowance would add significant wall thickness and weight, or when the fluid demands a corrosion resistant alloy. Clad pipe to API 5LD with a thin Alloy 625 liner in a carbon steel carrier is usually the economic answer for high rate wet gas service.

Q: Why do field joint coatings fail more often than mill coatings?
Because they are applied in a marine yard or on a lay vessel where surface preparation, humidity and cure time are harder to control, and the sleeve edge is a geometric stress concentration that peels if the cut back and taper are not correct.

Q: Does an aluminium anode work in all seawater conditions?
Aluminium-zinc-indium anodes are suitable for most seawater and marine sediment applications, but performance depends on the alloy composition and on electrochemical capacity testing, and zinc anodes are traditionally preferred in low temperature or low salinity environments where aluminium passivation is a risk.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry