What GOST 550 Actually Covers
GOST 550 is the seamless steel tube standard for the oil refining and petrochemical industries, and it is one of the most frequently specified Russian-language tube standards in process plant procurement. It covers hot-deformed seamless tubes produced from carbon and low alloy steel grades, and it defines the dimensional range, the steel grades permitted, the delivery condition, the mechanical property requirements and the test regime that a tube must satisfy before it can be released.
The standard is usually read together with GOST 8732 for the dimension and mass range of hot-deformed seamless tubes and with GOST 3845 for the hydrostatic test method. Steel 20, written in the Russian convention as stal 20, is the plain carbon grade within that family and accounts for the largest share of refinery piping, furnace coil supports, heat exchanger shells and general process lines supplied to this specification.
Steel 20: Chemistry and What the Number Means
In the GOST designation system the number following the word steel is the nominal carbon content in hundredths of a percent, so steel 20 contains approximately 0.20 % carbon, specified as a range of 0.17 to 0.24 %. That is a mild, low carbon, fully rimmed or killed steel with no deliberate alloy addition, and it is chemically close to the European C22 and the American AISI 1020 family.
| Element | Specified range, % | Practical significance |
|---|---|---|
| Carbon | 0.17 to 0.24 | Sets the strength ceiling and the weldability window |
| Silicon | 0.17 to 0.37 | Deoxidation; above 0.25 % indicates killed steel |
| Manganese | 0.35 to 0.65 | Strength and toughness balance; keeps sulphur cracking risk low |
| Phosphorus | 0.030 maximum | Restricts segregation and temper brittleness |
| Sulphur | 0.035 maximum | Controls inclusion level and through thickness ductility |
| Chromium | 0.25 maximum | Residual element, not an alloying addition |
| Nickel, copper | 0.30 maximum each | Residual elements from scrap |
The low carbon and low manganese content is the reason this grade behaves so predictably in fabrication. Carbon equivalent by the International Institute of Welding formula stays around 0.30 to 0.36, well below the 0.40 threshold at which preheat becomes mandatory for most wall thicknesses, so field welding without preheat is normally acceptable for standard walls under conventional heat input.
Mechanical Requirements in the As-Delivered Condition
The strength level required by the standard is modest by modern line pipe standards, and that is deliberate. Refinery and petrochemical piping is designed for moderate pressure at temperatures where carbon steel remains ductile, and the design codes reward ductility and toughness rather than minimum weight. A tube that meets the strength requirement with a comfortable margin in elongation is a more useful product than one that reaches a higher strength class at the cost of weldability.
| Property | Requirement for steel 20 | Comment |
|---|---|---|
| Tensile strength | Not less than 412 MPa | Corresponds to roughly 42 kgf per square millimetre |
| Yield strength | Not less than 245 MPa | Approximately 25 kgf per square millimetre |
| Elongation | Not less than 21 % | Measured on the proportional test piece |
| Hydrostatic test | Per GOST 3845, pressure calculated from wall and diameter | Held without leakage or permanent deformation |
| Flattening and bending | Required on designated sizes | Demonstrates ductility of the tube body and the weld free wall |
Because the tube is seamless, there is no weld seam and therefore no weld strength reduction factor. That is the property that most clearly separates this product from electric resistance welded tube of similar chemistry: the wall is metallurgically continuous around the full circumference, so the transverse and longitudinal properties are nearly identical.
Why Seamless Construction Matters in Refinery Service
Refinery and petrochemical service combines three conditions that penalise weld seams: cyclic thermal loading, wet sour or hydrogen bearing streams, and frequent hydrotest and steam-out cycles. A longitudinal weld in a welded tube is a metallurgical discontinuity with its own inclusion population, its own residual stress pattern and, in the as-welded condition, its own hardness profile through the heat affected zone.
In seamless tube produced by cross rolling piercing of a solid billet, the metal is deformed in three dimensions. The result is a wall with a favourable grain flow that follows the tube contour, no seam to inspect for lack of fusion or penetrator defects, and a far simpler acceptance route: visual and dimensional checks, wall thickness measurement, hydrostatic test and mechanical testing, without the weld specific non-destructive examination that welded tube requires. For small diameter and heavy wall combinations, seamless is also often the only commercially available option.
Manufacturing Route from Billet to Finished Tube
Production starts with a round steel billet cut to weight and heated to the rolling temperature. The billet is pierced on a rotary piercer to create a thick walled shell, then elongated on a plug mill, mandrel mill or assel mill depending on the size range, and finally sized and straightened. The deformation sequence determines the wall thickness tolerance and the eccentricity, which is the variation of wall thickness around the circumference.
Eccentricity is the single most important dimensional characteristic of hot-deformed seamless tube, because it forces the designer to add a corrosion allowance or a thickness margin on top of the calculated wall. A tube with a nominal wall of 8 mm and an eccentricity of 12.5 % has a thin point of 7 mm, and the entire pressure rating is set by that thin point. Buyers who care about material cost should specify the wall tolerance class and the permissible deviation rather than the nominal wall alone.
Heat treatment is applied where the order requires it. Normalising is the common route for steel 20, producing a uniform ferrite and pearlite structure with predictable strength and good toughness. Tubes may also be supplied as hot rolled without separate heat treatment, provided the mechanical properties meet the standard after the finishing pass.
Service Envelope: Temperature, Pressure and Media
Steel 20 performs well in the temperature band from about minus 40 degrees Celsius up to roughly 450 degrees Celsius for non-critical components, with the upper limit set by the onset of creep and by graphitisation risk in long term high temperature exposure. In the lower part of that band the material retains adequate Charpy energy, which is why it is used for cold climate installations in the refining industry.
The pressure capability comes from wall thickness, not from the grade. A steel 20 tube of adequate wall will satisfy the same design pressure as a higher grade tube of thinner wall, and the choice between the two is an economic and fabrication question rather than a safety question. Where the stream contains wet hydrogen sulphide, however, the hardness of the steel and of its welds becomes a hard limit, and the acceptance criteria of ISO 15156 and NACE MR0175 apply alongside the tube standard.
The grade is not intended for high temperature hydrogen service, for which chromium-molybdenum grades are required, nor for oxidising acid service, where stainless or nickel alloy tube is appropriate. Its corrosion resistance is that of ordinary carbon steel: acceptable in dry hydrocarbon and neutral aqueous service, poor in dilute acids and in chloride bearing wet streams.
Fabrication, Welding and Heat Treatment Notes
Steel 20 welds readily by shielded metal arc, gas tungsten arc and gas metal arc processes. Filler metal selection should match the base metal strength rather than exceed it substantially, because an overmatched weld on a low carbon pipe concentrates strain in the softer parent metal. Preheat is generally unnecessary below about 25 mm wall at ambient temperature above 0 degrees Celsius, but the joint should be dry and free of frost, and a modest preheat of 50 to 100 degrees Celsius is prudent for thick wall or high restraint joints.
Post-weld heat treatment is not normally required for steel 20 at ordinary wall thickness. It becomes advisable for thick sections, for joints with high restraint, and for service in wet sour environments where hardness control in the heat affected zone is a acceptance condition. Where it is applied, the holding temperature and the cooling rate should be recorded, because slow cooling through the embrittling range can degrade toughness even while the hardness survey looks satisfactory.
Bending and forming are straightforward in the normalised condition. Cold bending of thin wall tube is practical up to moderate radii, but the bend zone work hardens and should be stress relieved where the design code requires it. Hot bending requires temperature control to avoid overheating the steel above the point at which grain growth becomes excessive.
Ordering and Acceptance Checklist
A complete order for this product should state the standard and the steel grade, the outside diameter and wall thickness with the applicable tolerance class, the length and the length tolerance, the delivery condition, whether a hydrostatic test is required and at what test pressure, whether flattening or bending tests apply, and the marking and certificate requirements.
On receipt, verify four things. First, that the certificate quotes the correct standard and grade and that the heat number matches the tube marking. Second, that the tensile results meet 412 MPa tensile, 245 MPa yield and 21 % elongation, with the test piece location stated. Third, that the dimensions are within the specified tolerance, measured at both ends and at mid length, since ovality and wall eccentricity vary along the tube. Fourth, that the surface is free of the defects that matter for pressure service: longitudinal laps, seams, cracks and deep roll marks. Where the tube is destined for a pressure boundary, request the hydrostatic test record rather than a statement of compliance.
How Steel 20 Compares with Other Carbon Pipe Grades
Buyers frequently need to substitute an equivalent grade when GOST material is unavailable. The nearest technical equivalents are the Chinese 20 steel to GB/T 8163 for seamless tubes for liquid service, and the American ASTM A106 Grade B specification for seamless carbon steel pipe for high temperature service. All three share a carbon content near 0.20 % and a ferrite-pearlite microstructure.
The equivalence is close but not exact, and the differences matter at the margins. ASTM A106 Grade B requires a higher minimum tensile strength of 415 MPa with a minimum yield of 240 MPa, so strength is comparable, but its chemistry limits and its test frequency differ, and its dimensional tolerances follow a different system. A substitution should therefore be documented as a technical deviation with the dimensional, chemical and mechanical differences assessed against the design code, rather than accepted as an automatic swap on the basis of a grade cross reference table.
FAQ
Q: What does the number 20 mean in GOST steel 20?
It indicates a nominal carbon content of about 0.20 %, specified as 0.17 to 0.24 %. It is a plain carbon steel with no deliberate alloy addition, comparable in chemistry to the AISI 1020 family.
Q: Is GOST 550 tube always seamless?
Yes. GOST 550 covers seamless hot-deformed tubes for the oil refining and petrochemical industries. There is no welded variant within this standard, which is precisely why it is chosen for pressure and cyclic service.
Q: What are the minimum mechanical properties for steel 20 tube?
Tensile strength of at least 412 MPa, yield strength of at least 245 MPa and elongation of at least 21 %. These are modest values chosen to guarantee ductility and weldability rather than minimum weight.
Q: Can steel 20 tube be used at low temperature?
It is generally used down to about minus 40 degrees Celsius for non-critical components, provided the impact properties are verified for the actual service temperature. Below that range a low temperature grade with specified Charpy energy is required.
Q: Does GOST 550 tube need post-weld heat treatment?
Not for ordinary wall thickness in benign service. It becomes advisable for thick wall, high restraint joints, and it is required where a hardness ceiling applies, such as wet sour service under ISO 15156 and NACE MR0175.
Q: What is the main dimensional risk with hot-deformed seamless tube?
Wall eccentricity. The pressure rating is governed by the thinnest point of the wall, so a nominal wall with high eccentricity behaves like a thinner tube. Specify the wall tolerance class and measure thickness at several positions around the circumference.





