Nov 28, 2024 Leave a message

API 5L X52 Material Properties, Composition and Weldability

>X52 in Context

API 5L X52 is a medium-strength line pipe grade with a specified minimum yield strength of 360 MPa, or 52,200 psi, and a specified minimum tensile strength of 460 MPa. Its ISO 3183 and GB/T 9711 designation is L360, and pipe supplied for export is commonly dual marked with both names. The grade is popular because it delivers useful pressure capacity while remaining tolerant of normal field welding practice, which keeps qualification and construction costs predictable.

>Mechanical Properties

Property Requirement
Minimum yield strength 360 MPa / 52,200 psi
Minimum tensile strength 460 MPa / 66,700 psi
Upper yield strength, PSL2 Limited above the specified minimum
Yield to tensile ratio, PSL2 Capped by the standard to retain ductility
Elongation Determined by the standard formula based on tensile strength and cross-sectional area
Hardness, PSL2 250 HV10, 250 HBW or 22 HRC maximum
Impact toughness, PSL2 Charpy V-notch test mandatory, with test temperature and energy agreed for the project

The upper yield strength limit and the yield to tensile ratio cap distinguish PSL2 from PSL1 material and matter where girth welds must match the strength of the pipe body. Pipe with an unusually high yield strength relative to its tensile strength can behave with reduced strain capacity during installation.

>Chemical Composition

Element PSL1 PSL2, R, N and M conditions PSL2, Q condition
Carbon 0.28 % max seamless, 0.26 % max welded 0.24 % max seamless, 0.22 % max welded 0.18 % max
Manganese 1.40 % max 1.40 % max 1.60 % max
Phosphorus 0.030 % max 0.025 % max 0.025 % max
Sulphur 0.030 % max 0.015 % max 0.015 % max
Carbon equivalent Not controlled Limited for the grade range Limited for the grade range

Strength is achieved through manganese and through micro-alloying with niobium, vanadium and titanium, whose combined content is capped by the standard. A controlled carbon equivalent is what makes X52 PSL2 weldable with conventional procedures while retaining toughness at low temperature.

>Typical Applications

Oil and gas transmission pipelines in the medium pressure range.

Gathering lines, flow lines and station piping.

Water transmission and industrial process lines.

Structural tubulars and piling where a certified yield strength is required.

Slurry and tailings lines in mining service.

>Weldability and Fabrication

X52 is one of the more forgiving line pipe grades to weld. Procedures are qualified to API 1104 or ISO 13847, and both cellulosic and low-hydrogen consumables are used depending on the ambient conditions and the required toughness. Preheat is normally controlled by wall thickness and by the carbon equivalent of the actual heat of steel, and heat input is limited so that heat-affected zone toughness is not degraded. The internal and external surfaces of the pipe end are cleaned and the bevel dimensions verified before welding, because mismatched wall thickness or an incorrect bevel preparation is a frequent cause of weld defects. Where the pipe is coated, the cut-back length must be respected so that coating residue does not enter the weld pool. For sour service, the pipe is ordered with restricted chemistry and a lower hardness maximum, and the welded joints are hardness surveyed.

>FAQ

Q: What are the strength values of API 5L X52?
X52 has a specified minimum yield strength of 360 MPa, equal to 52,200 psi, and a specified minimum tensile strength of 460 MPa, equal to 66,700 psi.

Q: What is the equivalent of X52 in ISO 3183?
The equivalent designation is L360. The two names refer to the same minimum yield strength expressed in megapascals and in thousands of pounds per square inch.

Q: What does the maximum carbon content of X52 depend on?
It depends on the product specification level and the delivery condition. PSL1 allows 0.28 % for seamless pipe, PSL2 in the R, N and M conditions allows 0.24 %, and the Q condition allows 0.18 %.

Q: Why is carbon equivalent controlled in X52 PSL2?
Carbon equivalent predicts how the steel will behave during welding. Limiting it reduces the risk of hard, crack-sensitive microstructures in the heat-affected zone and allows a simpler welding procedure.

Q: Can X52 pipe be used at low temperature?
Yes, when the pipe is ordered with a suitable Charpy test temperature and the measured absorbed energy satisfies the project requirement. The impact requirement must be stated in the purchase order.

Q: What is the maximum permitted hardness of X52 PSL2?
The standard limits PSL2 pipe to 250 HV10, 250 HBW or 22 HRC. Sour service specifications often set a lower maximum for the pipe body and the welded joint.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry