Oct 08, 2024 Leave a message

Nominal Pressure vs Working Pressure in Steel Piping Systems

Four Different Pressures Behind One Piping Datasheet

Steel pipe and pipe fittings are ordered, rated and tested against four pressures that are frequently conflated in commercial documents: nominal pressure, design pressure, working pressure and test pressure. They answer four different questions. Nominal pressure defines what the component can withstand at a reference temperature. Design pressure defines the maximum pressure the piping system is engineered for, and it is the number from which wall thickness is calculated. Working pressure defines the maximum pressure actually reached during normal operation, including operating upsets. Test pressure defines the proof level applied at the mill or on site before the system is accepted.

A pipe can satisfy one of these numbers and fail another, which is why an order written only as "PN25 pipe" carries little engineering information. The buyer needs to know the reference temperature behind the rating, the design temperature and the fluid, and whether the pipe is supplied against a dimensional standard alone or against a pressure-retaining specification with a hydrostatic test.

Nominal Pressure: A Rounded Reference-Temperature Rating

Nominal pressure, designated PN, is a convenience rating. It expresses the pressure resistance of a component at a defined reference temperature, and the value is a rounded number originally intended to give a compact series of flange and fitting ratings: PN 6, PN 10, PN 16, PN 25, PN 40, PN 63, PN 100, PN 160, PN 250, PN 320 and PN 400 in the European system. Because it is a rounded reference value rather than a calculated allowable pressure, the PN number must always be read together with a temperature derating curve published in the applicable standard, such as EN 1092-1 for flanges or the relevant part of EN 10216 for tube.

Two features of PN are commonly misunderstood. First, PN is not the pressure at which the component will be proof tested; a PN 16 flange is routinely pressure tested well above 16 bar. Second, PN does not directly describe wall thickness. In the European flange system the rating determines flange dimensions, while the pipe wall thickness that can be attached to it is governed by the pipe dimensional standard and by the design calculation for the system.

Design and Working Pressure: The Numbers That Govern Wall Thickness

Design pressure is the maximum internal or external pressure used in the mechanical design of the piping system. Under ASME B31.3 it is established by the owner together with the design temperature, and it is the input to the wall thickness equation for straight pipe under internal pressure, in which the required thickness depends on design pressure, outside diameter, allowable stress at design temperature, weld joint quality factor and the temperature coefficient. Working pressure, by contrast, is an operating reality: it is the highest pressure the system sees in service, including pump shut-off head, surge, and relief valve set points.

In a correctly designed system the working pressure stays below the design pressure with margin. The margin exists because design pressure also has to cover the reduced allowable stress at elevated temperature, corrosion or erosion allowance, and the practical thickness tolerances permitted by the pipe standard. When a purchase order states only a working pressure and no design pressure or design temperature, the mill cannot verify that the ordered wall thickness is adequate, and any implied approval is meaningless.

Units and Rating Systems: PN, Class and Schedule in One Frame

Two rating languages coexist in international piping. The metric system uses PN in bar-equivalent terms, while the North American system uses Class designations, from Class 150 to Class 2500, defined in ASME B16.5 for flanges and ASME B16.47 for large diameter flanges. The two are not numerically interchangeable, particularly at the lower end, and mixing them in one specification is a common source of dimensional mismatch between flanges and fittings.

Nominal pressure (metric) Nearest ASME Class Approximate cold working pressure for carbon steel, bar Typical application
PN 10 below Class 150 about 10 low pressure water and utility lines
PN 16 Class 150 about 16 to 19 general building services, low pressure steam
PN 25 Class 150 / Class 300 boundary about 25 process water, compressed air headers
PN 40 Class 300 about 40 to 51 process piping, moderate pressure steam
PN 63 Class 400 about 63 high pressure process service
PN 100 Class 600 about 100 high pressure steam and hydrocarbon service
PN 160 Class 900 about 160 power plant high pressure systems
PN 250 Class 1500 about 250 very high pressure process and boiler feed lines
PN 420 Class 2500 about 420 extreme pressure special service

The conversion shown is approximate by design: the two systems were built on different reference temperatures and different safety philosophies, so a PN 40 flange and a Class 300 flange share a nominal rating band but have different bolt circles, different facing dimensions and different thickness. A flanged joint assembled from mixed metric and inch components will leak regardless of how carefully the gasket is torqued.

Reference Temperature and Why Every Rating Must Be Derated

All nominal ratings are anchored to a reference temperature, and the reference temperature differs by material group. For carbon steel flanges and fittings, the reference temperature in the European system is generally 20 °C, with the rating held constant only up to a modest temperature and then reduced in steps. In older conventions a base temperature of 250 °C was sometimes quoted for steel, which is one reason legacy documents contain rating tables that appear inconsistent with current standards.

Above the reference temperature the allowable pressure falls because the allowable stress of the material falls. For carbon steel the drop is modest up to roughly 200 °C, becomes significant in the 300 to 400 °C range, and steepens further as creep becomes the governing design condition. For austenitic stainless steel the curve is flatter at moderate temperature but still requires derating, and the applicable table must be the one belonging to the specific material group rather than to steel in general.

The practical consequence for a purchaser is direct. A line rated PN 40 for ambient water duty is not automatically a PN 40 line at 350 °C saturated steam; the allowable pressure at that temperature may be less than half the cold rating, and the correct wall thickness has to be recalculated from the allowable stress at design temperature. Temperature is therefore never optional information on a pipe specification.

Test Pressure: What the Mill Actually Proves

Test pressure is the pressure applied to prove integrity, and its level and duration are set by the product standard rather than by the purchaser's expectation. Seamless and welded line pipe ordered to API 5L is hydrostatically tested in accordance with that specification, with the holding time and the pressure level related to the specified minimum yield strength and the pipe geometry; non-destructive alternatives are permitted in defined circumstances. Pipe ordered to ASTM specifications is tested in accordance with ASTM A530/A530M or ASTM A999/A999M, which set the hydrostatic test pressure as a function of wall thickness and diameter together with a minimum and maximum practical limit.

On site, the system test is a different event again: it is normally a hydrostatic proof of the assembled system at a pressure above design pressure, held for a defined period, with the test pressure capped so that it does not overstress the lowest-rated component or the supports. Confusing a mill test with a system test leads to two familiar disputes, one about why the mill certificate shows a test pressure lower than the site test level, and one about why a system test damaged a valve or a gasket that was rated below the test pressure.

Reading the Documents: Datasheet, Standard and Mill Certificate

The three pressure concepts appear in three different documents, and cross-checking them is the core of technical due diligence on a pipe order.

Datasheet or line class: states design pressure, design temperature, fluid, nominal size, schedule or wall thickness, material grade and the applicable rating standard. This is where PN or Class appears.

Product standard: states the dimensional tolerances, the tensile and yield requirements, the hydrostatic or non-destructive test, and often a maximum allowable pressure for the finished product. For line pipe this is API 5L or ISO 3183; for boiler and heat exchanger tube it is ASME BPVC Section II Part A specifications such as SA106 or SA213, or EN 10216-2; for general service it is ASTM A53/A53M or ASTM A106/A106M.

Mill certificate: states the heat number, grade, dimensions, chemical composition, tensile results, test pressure applied and holding time, and the delivery condition. If the certificate shows no test pressure and no statement of exemption, the purchaser should ask why before the pipe enters the system.

Pressures Along the Wall: Where the Rating Lives

It is worth remembering that the nominal rating belongs to the fitting or flange, whereas the pressure capability of the pipe itself belongs to the wall. A PN 100 flange welded to a thin-wall pipe does not create a PN 100 line. The weak element governs, and in most systems the weak element is either the pipe wall at the design temperature or a component with a lower rating such as a valve, an expansion joint, or a threaded connection whose pressure capability is reduced by the cut thread.

Threaded and socket-welded joints deserve particular attention because their pressure capability falls with size and is limited by the thread form defined in ASME B1.20.1. It is not unusual for a line to be designed around a PN 63 rating and then be limited in practice by a threaded branch connection that is only suitable for a much lower pressure at the same temperature.

Common Misunderstandings and How to Avoid Them

Several errors recur so often that they are worth writing into a procurement checklist. Treating PN as a test pressure leads to over-testing and distorted flanges. Treating the cold rating as valid at design temperature leads to under-thickness pipe in hot service. Mixing PN and Class components on one joint leads to leaks and to non-conformance at inspection. Assuming that a higher schedule number means a higher pressure rating ignores the fact that schedule numbers are dimensional, not rating, designations, and that for small sizes a higher schedule can mean a heavier wall than the nominal schedule of the same number in a larger size.

The safest discipline is simple: specify design pressure and design temperature explicitly, name the rating standard and edition to be applied, state whether the pipe is ordered to a pressure-retaining specification with hydrostatic test, and require the mill certificate to record the test pressure and holding time. That set of four statements removes almost all room for divergent interpretation between buyer and mill.

FAQ

Q: Is nominal pressure the same as the maximum allowable pressure of a fitting?
No. Nominal pressure is a rounded reference-temperature rating. The maximum allowable pressure at a given service temperature is obtained by applying the derating table of the relevant standard to that nominal rating, and it is always lower than the nominal value at elevated temperature.

Q: Does a higher nominal pressure automatically mean a thicker pipe wall?
No. The nominal pressure fixes flange and fitting geometry, while pipe wall thickness comes from the design calculation using design pressure, diameter and allowable stress at design temperature. A PN 40 flange can be attached to several different wall thicknesses depending on the pipe schedule selected.

Q: Why is working pressure different from design pressure?
Design pressure is the engineered maximum used to size the system. Working pressure is the highest pressure actually reached in operation, including surge and relief settings, and it is kept below design pressure so that the design margin covers temperature derating, corrosion allowance and tolerances.

Q: What test pressure is applied to a seamless pipe at the mill?
The level is set by the product standard. Line pipe to API 5L or ISO 3183 is hydrostatically tested per that specification, and pipe to ASTM specifications follows ASTM A530/A530M or ASTM A999/A999M, which relate test pressure to wall thickness and diameter and impose practical upper limits on the applied pressure.

Q: Can a Class 150 flange be bolted to a PN 16 flange of the same size?
They share a similar rating band but not the same dimensions. Bolt circle, bolt hole diameter, facing and thickness differ between the metric and inch systems, so the pair will not seal reliably. Components on one joint should come from one rating system.

Q: How much does temperature reduce the pressure rating of carbon steel pipe?
The reduction is small up to about 200 °C and becomes significant above roughly 300 °C, when the allowable stress of carbon steel falls and creep starts to govern. The exact factor must be taken from the derating table for the specific material group and design temperature, not estimated.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry