Two Pipe Families, One Specification Language
Carbon steel pipe and stainless steel pipe are both ordered against recognised product specifications, yet the two families answer different engineering questions. A carbon steel pipe works on a carbon-manganese chemistry, usually 0.08 % to 0.30 % carbon with manganese as the main strengthener, and depends on an external barrier, such as paint, fusion bonded epoxy, three-layer polyethylene or galvanising, to survive a corrosive environment. A stainless steel pipe works on a chromium-rich surface, typically 18 % to 20 % chromium with 8 % to 11 % nickel in the austenitic grades, so that a chromium oxide passive film re-forms by itself after cutting, welding or abrasion. The purchasing consequence is that the first family is specified by strength, toughness and wall thickness, while the second is specified by alloy type, surface condition and corrosion testing in addition to strength.
For a buyer the distinction is not strong versus weak. A seamless pipe to ASME SA106 Grade B reaches a minimum yield strength of 240 MPa and a minimum tensile strength of 415 MPa, which is higher than the 205 MPa yield and 515 MPa tensile of ASTM A312 TP304. What changes is how each material behaves when the fluid, the operating temperature, the chloride content and the installation method change. Reading a mill certificate without that context is the most common source of wrong selection on export orders.
Chemical Composition and the Grade Families That Follow From It
Composition is the root of every downstream difference, from weldability to pressure rating. In carbon and carbon-manganese pipe the carbon equivalent controls weldability: ASME SA106 Grade B limits carbon to 0.30 % with manganese between 0.29 % and 1.06 %, silicon 0.10 % minimum, phosphorus and sulfur 0.035 % maximum each. Line pipe to API SPEC 5L adds strength through micro-alloying and controlled rolling rather than carbon, which is why API 5L X52 PSL2 achieves 359 MPa minimum yield with carbon kept near 0.22 % or lower and a carbon equivalent limit imposed by the specification for weldability.
In stainless pipe the chromium content defines the family. Ferritic grades such as ASTM A268 rely on chromium alone and are magnetic. Austenitic grades to ASTM A312 add nickel to stabilise the austenite, giving the face-centred cubic structure that provides ductility at cryogenic temperature. Duplex grades to ASTM A789 and A790 balance roughly equal fractions of ferrite and austenite with about 22 % chromium, 3 % molybdenum and 0.15 % nitrogen, delivering a yield strength of 450 MPa minimum, more than double that of TP304.
| Grade | Product standard | C max, % | Cr, % | Ni, % | Mo, % | Typical duty |
|---|---|---|---|---|---|---|
| SA106 Gr.B | ASME BPVC II-A | 0.30 | 0.40 max | 0.40 max | 0.15 max | Steam, water, oil up to about 400 C |
| API 5L X52 PSL2 | API SPEC 5L | 0.22 typical | - | - | - | Oil and gas transmission, sour and sweet |
| TP304 / S30400 | ASTM A312 | 0.08 | 18.0-20.0 | 8.0-11.0 | - | Food, potable water, general chemical |
| TP316L / S31603 | ASTM A312 | 0.035 | 16.0-18.0 | 10.0-14.0 | 2.00-3.00 | Chloride-bearing process water, marine air |
| TP321 / S32100 | ASTM A312 | 0.08 | 17.0-19.0 | 9.0-12.0 | - | High temperature, thermal cycling, Ti stabilised |
| S32205 duplex | ASTM A790 | 0.030 | 22.0-23.0 | 4.5-6.5 | 3.0-3.5 | Offshore, chloride stress corrosion, high pressure |
The molybdenum-bearing TP316L and the duplex S32205 also carry a higher pitting resistance equivalent number, calculated as Cr + 3.3 Mo + 16 N. TP304 sits near 19, TP316L near 25 and S32205 near 35, so the three grades separate clearly in seawater splash zones. That single number explains why a grade substitution from TP304 to TP316L is not cosmetic when chlorides are present.
Mechanical Properties and How They Are Verified
Mechanical requirements are stated per product specification and per specimen orientation, and the tensile test is the acceptance gate. Carbon steel pipe to ASME SA106 and ASTM A53 is tested on the pipe body; stainless pipe to ASTM A312 requires tensile testing of each lot plus a flattening test and, for larger sizes, a non-destructive electric test. When a buyer compares two quotations, the strength figures should be read together with the required heat treatment condition, because the same grade in the annealed, normalised or cold-drawn condition delivers different numbers.
| Grade | Yield min, MPa | Tensile min, MPa | Elongation min, % | Hardness or condition note |
|---|---|---|---|---|
| SA106 Gr.B | 240 | 415 | 30 | As-rolled or normalised, no hardness ceiling |
| ASTM A53 Gr.B | 240 | 415 | Per table by size | Welded and seamless, hydrostatic test default |
| API 5L X52 PSL2 | 359 minimum | 455 minimum | Formula based on OD | CVN impact testing mandatory, 0 C or lower |
| TP304 | 205 | 515 | 35 | Solution annealed, Rockwell B 90 max |
| TP316L | 170 | 485 | 30 | Solution annealed, Rockwell B 90 max |
| S32205 duplex | 450 | 620 | 25 | Annealed and water quenched, ferrite ratio checked |
Ductility deserves a second look. The 10 % elongation figure quoted for 20Cr-type alloy structural steel belongs to a different product family and should never be applied to pipe. A pipe with 10 % elongation and a high yield strength is not a better pressure boundary; the pipe specifications require 25 % to 35 % so that field bending and weld root opening do not crack the material. Any certificate offering high strength with low elongation on a pipe order is a flag for product analysis and a repeat tensile test.
Corrosion Resistance, Temperature and the Real Service Limit
Carbon steel corrodes as a general thinning mechanism and the design answer is a corrosion allowance plus coating, with three-layer polyethylene to DIN 30670 or GB/T 23257, fusion bonded epoxy to ISO 21809-2, or hot dip galvanising to ISO 1461. Stainless steel resists general corrosion but fails locally, through pitting, crevice attack, intergranular attack after sensitisation and chloride stress corrosion cracking. Localised failure is far less predictable, which is why the stainless specification must state the service environment rather than only the grade.
Temperature sets another boundary. Carbon and carbon-manganese pipe is limited by graphitisation and oxidation for long-term high temperature duty, and ASME SA106 gives allowable stresses only up to the range tabulated in Section II Part D. Austenitic stainless pipe serves to higher temperature, but between roughly 425 C and 815 C chromium carbides precipitate at grain boundaries in unstabilised grades, so TP321 with titanium addition of at least five times the carbon content, or the low-carbon TP304L, is preferred for welded assemblies that see that range. Duplex grades must not be used above about 300 C, where the ferrite phase embrittles.
Water chemistry decides more than the alloy label. Chloride stress corrosion cracking of austenitic stainless is a real risk above roughly 60 C in chloride-bearing water, while duplex and super-austenitic grades with molybdenum raise the threshold substantially. For sour hydrocarbon service, ISO 15156 and NACE MR0175 define the acceptable hardness and chemistry envelope, and neither carbon steel nor standard austenitic grades are automatically acceptable.
Manufacturing Routes and the Effect on Wall Tolerance
Carbon steel pipe is produced seamless by piercing a heated billet and rolling or cold drawing to size, or welded from strip by electric resistance welding, longitudinal submerged arc welding or spiral submerged arc welding. Stainless pipe is produced seamless by extrusion or piercing and cold pilgering, and welded by continuous roll forming with tungsten inert gas or plasma arc, followed by full solution annealing of the weld zone. The route determines both the dimensional tolerance and the metallurgical condition of the delivered pipe.
Wall thickness tolerance is where the two families diverge commercially. Seamless carbon pipe is commonly supplied to a minus tolerance of 12.5 % on wall and plus tolerance on outside diameter, so the buyer must specify whether the ordered wall is nominal or minimum. Welded pipe holds wall tolerance tightly because it is formed from strip of controlled thickness, but it carries a weld seam that requires a weld quality factor in pressure design. Cold-drawn stainless and precision tube holds tighter concentricity and is specified with an inside diameter tolerance when the bore is the functional surface.
Straightness, ovality and end squareness matter for automatic welding. For orbital welding of stainless hygienic lines, the outside diameter and wall tolerance of ASTM A270 or ASTM A269 tube is far tighter than commercial pipe; substituting pipe for tube in such a system creates root gaps that no welder can close reliably.
Welding, Heat Treatment and Fabrication Differences
Carbon steel pipe welds with conventional processes and needs preheat only as a function of thickness, carbon equivalent and restraint. Stainless pipe needs a different discipline: low heat input, argon or argon-hydrogen shielding with a purge on the root side, avoidance of carbon steel tooling to prevent iron contamination, and cleaning of the heat tint afterwards. Iron contamination on stainless steel becomes a corrosion initiation site, and grinding dust from carbon steel fabrication is enough to cause rust staining on an otherwise correct installation.
Post-weld treatment is the second divergence. Carbon steel welds are stress relieved to control hardness in sour or thick-wall service. Austenitic stainless welds are not stress relieved in the same way; they are solution annealed at a minimum of 1040 C followed by rapid cooling when the specification to ASTM A312 applies to the finished product, and welds are otherwise left with a controlled ferrite content to resist hot cracking. Duplex welds require a balanced heat input and nitrogen in the shielding gas to restore the austenite fraction in the weld metal.
Post-fabrication cleanliness is a specification item, not housekeeping. Pickling and passivation to ASTM A380, with test methods to ASTM A967, restores the chromium oxide film after welding and removes heat tint and free iron. Skipping that step on a stainless line leaves it less corrosion resistant than the mill product that was certified.
Inspection, Testing and Documentation
Acceptance testing follows the product standard and should be named in the purchase order rather than assumed. Both families require a mill test certificate to EN 10204 3.1 with chemical composition and tensile results traceable to the heat number. Beyond that, carbon steel pipe typically receives a hydrostatic test and, where specified, ultrasonic testing of the seam to ISO 10893 or ASTM E213. Stainless pipe receives a hydrostatic test or an electric test to ASTM E426, flattening and reverse flattening, and on request an intergranular corrosion test to ASTM A262 practice E for the unstabilised austenitic grades.
Positive material identification is the practical defence against a mixed mill bundle. Handheld X-ray fluorescence confirms chromium, nickel and molybdenum in seconds and detects a TP304 pipe placed in a TP316L bundle, or a carbon steel fitting placed with stainless. Dimensional verification covers outside diameter, wall thickness at four points, length, and end preparation such as bevel angle and root face. For line pipe, the impact test series and the drop weight tear test results are reviewed against the toughness requirement of the order.
Cost Structure and Procurement Comparison
Per tonne, stainless pipe commonly costs three to five times carbon steel pipe, and the ratio moves with the nickel and molybdenum markets. Two thirds of the stainless price is alloy cost carried as a surcharge, so quotations should state the alloy surcharge basis and the validity period instead of a single lump figure. Carbon steel pipe is driven by hot rolled coil and billet prices plus coating cost, and a change from bare to three-layer polyethylene can add a significant share to the delivered metre price.
The comparison should be made on installed cost, not on pipe price alone. Stainless pipe is often thinner-walled for the same pressure duty because of higher allowable stress and no corrosion allowance, and it needs no internal lining or external repainting over life. Carbon steel needs coating, cathodic protection in buried service, and periodic inspection for wall loss. For a 20-year life in a chloride environment, the stainless option frequently wins on lifecycle cost even at a much higher initial price.
Selecting Without Guesswork
Start from the fluid, its chloride content, the operating and design temperature, and the design code. Then fix the family, the grade and the wall thickness, in that order. State the product specification with its edition reference, the delivery condition, the test schedule and the documentation level. Ask for the heat number, the product analysis and the heat treatment record, and check that the elongation and toughness figures belong to the pipe specification rather than to a bar or forging standard. Where a substitution is proposed, compare composition first; a change of nickel or molybdenum content outranks any improvement in tensile strength for corrosion duty.
FAQ
Q: Is stainless steel pipe always stronger than carbon steel pipe?
No. ASME SA106 Grade B provides 240 MPa minimum yield against 205 MPa for ASTM A312 TP304, while duplex S32205 reaches 450 MPa. Stainless wins on corrosion resistance and on strength at elevated temperature, not automatically on room-temperature strength.
Q: Can I replace a carbon steel pipe with TP304 for the same pressure rating?
Only after rechecking the wall thickness against the allowable stress of the stainless grade in the design code. TP304 has a lower allowable stress than carbon steel in some temperature ranges, so an identical wall may not carry the same pressure, and the two materials also differ in thermal expansion by roughly 40 %.
Q: Why does a stainless pipe rust after installation?
Rust stains on austenitic stainless usually come from free iron contamination, heat tint left after welding, or chlorides trapped in a crevice. Removal requires pickling and passivation to ASTM A380 with testing to ASTM A967, and the source of contamination must be corrected.
Q: What is the difference between TP304 and TP304L?
TP304 limits carbon to 0.08 % and TP304L to 0.035 %. The low-carbon variant resists chromium carbide precipitation during welding, so intergranular corrosion risk in the heat affected zone falls, at the cost of slightly lower minimum yield strength of 170 MPa against 205 MPa.
Q: Which test proves that a stainless pipe will resist intergranular corrosion?
ASTM A262 practice E, the copper-copper sulfate sulfuric acid test, is the standard acceptance test for austenitic grades, applied after sensitising. It detects susceptibility caused by wrong chemistry or wrong annealing, and it does not replace a pitting test for chloride service.
Q: When is a duplex pipe the better choice over TP316L?
When the service combines chlorides, higher pressure and a moderate temperature ceiling. Duplex S32205 delivers about 450 MPa yield and a pitting resistance equivalent near 35, but it must be kept below roughly 300 C and welded with a qualified procedure that preserves the ferrite-austenite balance.





