What EN 10210 S355J2H Designates
EN 10210 is the European standard for hot-finished structural hollow sections of non-alloy and fine-grain steels. It is published in two parts: EN 10210-1 gives the technical delivery conditions, and EN 10210-2 gives dimensions, tolerances and section properties. The grade designation S355J2H decomposes into four pieces of information that a buyer can act on directly. S means structural steel, 355 is the minimum specified yield strength in megapascals at the reference thickness, J2 denotes a Charpy impact requirement of 27 J minimum at minus 20 degrees Celsius, and H identifies the product as a hollow section rather than a flat or long product. The material number 1.0576 identifies the same grade in the numeric system used across European design offices.
Because the H suffix is part of the designation, S355J2H properties are specified for the hollow section as delivered. That is not a formality. The same steel rolled as plate and formed into a section has a different thermal and strain history, and the impact requirement in particular is certified on the finished hollow section, not on the coil or plate it came from. A mill certificate that reports impact energy from the input material does not demonstrate compliance with S355J2H.
EN 10210 also fixes the delivery condition. Hot-finished hollow sections are either seamless, hot formed from a heated billet, or welded and subsequently heat treated so that the finished section, weld included, is brought above the upper critical temperature and normalized. That full-section treatment is what distinguishes EN 10210 welded sections from EN 10219 cold-formed welded sections, which are delivered without a post-weld normalizing treatment and carry correspondingly different impact and residual stress behaviour.
Chemical Composition and Fine-Grain Control
The composition limits for S355J2H are moderate but they are not the whole story, because EN 10210-1 also caps carbon equivalent. That cap is what makes the grade reliably weldable in thick sections without preheat in most shop conditions, and it is a clause that buyers should verify on the certificate rather than assume.
| Element / index | Limit for S355J2H | Why it matters |
|---|---|---|
| Carbon | 0.22 % max | Strength versus weld-zone hardness and toughness |
| Silicon | 0.55 % max | Deoxidation; high silicon affects galvanizing appearance |
| Manganese | 1.60 % max | Strength and toughness balance |
| Phosphorus | 0.030 % max | Toughness, and coating quality after galvanizing |
| Sulfur | 0.030 % max | Weld quality, resistance to lamellar tearing |
| Carbon equivalent (CEV) | 0.45 max for this grade | Weldability and preheat decisions in thick walls |
Fine-grain designations in the standard, including the normalised and normalised-rolled variants, add restrictions on grain-refining elements and on the aluminium or niobium and titanium content needed to keep the ferrite grain size fine. That is the mechanism behind the low-temperature impact performance. A supplier that offers "S355J2H equivalent" chemistry without the fine-grain control can match the tensile numbers and still fail the impact test at minus 20 degrees Celsius, so the grade statement on the certificate must be exactly S355J2H rather than a chemistry description.
The manganese range is the visible difference from plain carbon structural steel. Raising manganese to the 1.6 % ceiling improves toughness and hardenability, which is why the grade performs in cold climates and under dynamic loading where S235JRH would be marginal. It also raises carbon equivalent, which is why the CEV cap exists and why thick-wall S355J2H is usually welded with a modest preheat rather than a large one.
Mechanical Properties Across Wall Thickness
EN 10210 grades are thickness dependent: the specified minimum yield falls as the wall increases, because thicker sections cool more slowly and develop coarser microstructures. Reading a single yield value off a catalogue without checking the applicable thickness band is one of the most common technical errors in hollow section procurement.
| Property | Requirement for S355J2H |
|---|---|
| Minimum yield strength ReH, thickness up to 16 mm | 355 MPa |
| Minimum yield strength ReH, above 16 mm up to 40 mm | 345 MPa |
| Minimum yield strength ReH, above 40 mm up to 63 mm | 335 MPa |
| Minimum yield strength ReH, above 63 mm up to 100 mm | 325 MPa |
| Tensile strength Rm | 470 to 630 MPa |
| Minimum elongation, thickness up to 40 mm | 22 % |
| Charpy impact, J2 quality | 27 J minimum average at minus 20 degrees Celsius |
The 470 to 630 MPa tensile window is a two-sided requirement and both ends matter. Too low and the section cannot develop its design resistance. Too high and the material is harder and less ductile than the design assumptions expect, which affects bolted connection bearing behaviour, drilling and cold bending. A delivery that reports 640 MPa tensile is non-conforming even though the number looks impressive.
The J2 impact designation is the reason this grade is used in cold-climate and dynamically loaded structures. It requires a Charpy test set at minus 20 degrees Celsius, and the standard specifies both an average and a minimum single-value criterion. Where a project needs 40 J at minus 20 degrees Celsius, the correct designation is K2 rather than J2, and that distinction must appear in the purchase order because the mill will not upgrade the testing on its own initiative.
Manufacturing Route and the Seam Question
Seamless EN 10210 hollow sections are produced by piercing and rolling, then sizing and normalizing as required. Welded EN 10210 sections are formed from strip or plate, welded, and then given the full-section heat treatment that the standard requires. The heat treatment normalizes the weld and the heat-affected zone, refines the grain structure distorted by forming, and removes most of the residual stress from the weld and from the shaping operation. The result is a section whose properties are uniform around the perimeter, which is exactly what a structural designer assumes when a hollow section is loaded in combined bending and torsion.
This is where a frequent misunderstanding needs correcting. Helical-seam submerged arc welded pipe, the spiral pipe used for large-diameter line and piling work, is a different product route. Its weld is made on a continuously formed helix and is not normally followed by a full-section normalizing treatment, so spiral pipe is generally supplied against cold-formed hollow section standards such as EN 10219, against pressure pipe standards such as EN 10217 or API 5L, or against a project specification that defines the heat treatment separately. Describing a spiral-welded pipe as EN 10210 S355J2H implies a normalizing treatment after welding that most spiral mills do not perform.
The practical consequence for a buyer is simple. If the project specification calls for EN 10210 S355J2H, buy a hot-finished hollow section and accept the size availability of that product. If the project needs a large-diameter spiral pipe, define the governing standard openly, state whether the weld is to be heat treated, and specify the impact and NDT requirements that the actual route can certify. Trying to obtain both from one product leads to either an unverifiable certificate or a rejected consignment.
Dimensions, Tolerances and Section Properties
EN 10210-2 fixes the dimensional tolerances and the tabulated section properties that designers use. The tolerances that affect fabrication are outside dimension, wall thickness, out-of-roundness or squareness, straightness, twist and mass. Seamless and welded sections are tabulated separately for wall tolerance because the two routes cannot hold the same control, and the buyer should confirm which table applies to the delivered route.
Wall thickness tolerance deserves particular attention because it propagates into every structural check. A section at the low end of the permitted wall range has a lower plastic modulus, lower buckling resistance and lower fatigue strength at welded details than the nominal section. Where a design has been optimised close to the limit, the purchase order should either specify a restricted wall tolerance or require the actual wall to be measured and reported per length.
Corner geometry and the flat width of the faces also matter. Hot-finished sections have generous outer corner radii, and a welded connection detailed into a corner must be assessed on the curved surface, not on a sharp corner. Concavity and convexity limits on the faces affect the contact quality of bolted end plates and the seating of clamps. Straightness limits are expressed as a proportion of length, so deviation grows with the length ordered; long lengths should be checked on a bed before acceptance rather than at the point of erection.
Fabrication, Welding and Corrosion Protection
S355J2H welds well in the shop and on site, but the welding procedure must be qualified for the grade and the thickness combination, not transferred from an S275 job. With carbon equivalent up to the 0.45 cap and walls above about 20 mm, a controlled preheat and a hydrogen-controlled consumable policy are normal good practice. Where the structure will be galvanized, the weld procedure should also minimize surface slag and avoid creating sealed cavities.
Corrosion protection follows the project system rather than the tube standard. Hot-dip galvanizing to ISO 1461 applies to fabricated articles and depends on venting and draining being designed in; painting and duplex systems fall under ISO 12944, with the corrosivity category determining the coating specification. Because galvanizing performance is sensitive to steel chemistry, a phosphorus level near the permitted maximum should be flagged before coating, even though it is fully compliant with EN 10210.
Fire protection and intumescent coating adhesion deserve an early decision, since the surface preparation specified for paint may differ from the preparation needed for the coating system. Tubing delivered with mill scale intact is not ready for either without surface treatment.
Inspection, Testing and Documentation for Buyers
The inspection certificate for EN 10210 product should identify the standard and part, the grade, the delivery condition, the dimensions and the heat number, and should report chemical analysis, tensile results and impact results taken from the finished hollow section. Non-destructive testing of the weld, where required, is specified by the purchaser and carried out to the ISO 10893 series or an agreed equivalent, with the acceptance level stated in the order because "NDT to the standard" is not a test severity.
A compact receiving inspection catches most problems. Measure outside dimension and wall at both ends and at mid-length. Check straightness over the full length and twist across the section. Confirm the impact test temperature and energy on the certificate, since a J0 certificate cannot substitute for J2. Confirm the delivery condition statement is present and consistent with the manufacturing route described by the mill. Where the section will be galvanized, verify that vent holes are in the fabrication drawing before the first member is dipped.
Applications and Grade Selection
S355J2H hollow sections are used in crane and conveyor structures, bridge and footbridge elements, stadium and roof trusses, offshore secondary structures, agricultural and mining equipment, and transport frames loaded in torsion or bending. Their high strength-to-weight ratio and their closed shape make them efficient in torsion, and the J2 impact quality makes them suitable for cold-climate service and for structures with repeated loading.
Selection is governed by three practical questions. Does the design need impact toughness at a stated temperature, in which case the J0, J2 or K2 designation must be selected deliberately? Is the member stiffness-critical, in which case a higher grade does not help and a larger depth does? Will the section be welded in thick wall, in which case the carbon equivalent and preheat policy must be checked at the design stage? Answering these before ordering avoids the two most expensive outcomes: paying for toughness that the design never uses, or discovering at fabrication that the delivered grade carries an impact designation the project cannot accept.
FAQ
Q: What does S355J2H mean in EN 10210?
S denotes structural steel, 355 is the minimum yield strength in MPa at the reference thickness, J2 requires 27 J minimum Charpy impact energy at minus 20 degrees Celsius, and H indicates a hollow section. The grade corresponds to material number 1.0576.
Q: What is the minimum yield strength of S355J2H?
355 MPa for wall thickness up to 16 mm, falling to 345 MPa above 16 mm up to 40 mm, 335 MPa above 40 mm up to 63 mm, and 325 MPa above 63 mm up to 100 mm, with a tensile strength range of 470 to 630 MPa.
Q: Is EN 10210 the same as EN 10219?
No. EN 10210 covers hot-finished hollow sections, and welded sections receive a full-section heat treatment after welding. EN 10219 covers cold-formed welded hollow sections delivered without that post-weld normalizing treatment, so impact behaviour and residual stress differ.
Q: Can spiral-welded pipe be certified as EN 10210 S355J2H?
Only if the finished section, weld included, receives the heat treatment required by the standard. Spiral pipe is normally supplied to cold-formed hollow section or pressure pipe standards, or to a project specification that defines heat treatment and weld testing explicitly.
Q: What is the difference between J0, J2 and K2 quality?
The letter and digit define the Charpy test temperature and minimum energy: J0 requires 27 J at 0 degrees Celsius, J2 requires 27 J at minus 20 degrees Celsius, and K2 requires 40 J at minus 20 degrees Celsius. The designation must be stated in the order.
Q: How is the weld inspected on EN 10210 hollow sections?
Non-destructive testing is a purchaser-specified requirement, commonly performed to the ISO 10893 series for tubular products, with the method, coverage and acceptance level agreed in the purchase order and recorded on the inspection document.





