Mar 19, 2024 Leave a message

L360 and X52 Line Pipe: Chemistry, Mechanical Properties and Delivery Conditions

What L360 Line Pipe Is

L360 is a line pipe grade with a specified minimum yield strength of 360 MPa, used for the pipeline transportation of oil, gas and water. It is the metric designation in ISO 3183 and GB/T 9711 of the grade written as X52 in the API 5L imperial table, the two numbers describing the same strength level expressed in MPa and in thousands of pounds per square inch.

Line pipe in this grade is made as seamless pipe or as welded pipe by electric resistance, high frequency, submerged arc or laser welding, and it is used where a moderate strength increase over L245 or L320 reduces the required wall thickness without making field welding difficult or expensive.

Grade Equivalence, Specification Levels and Delivery Conditions

System Designation Minimum yield strength Minimum tensile strength
ISO 3183 and GB/T 9711 L360 360 MPa 460 MPa
API 5L imperial table X52 52 000 psi 66 000 psi

PSL 1 pipe meets the chemistry and tensile requirements of the standard and is available in the as-rolled, normalized, quenched and tempered or thermomechanical conditions. PSL 2 adds mandatory carbon equivalent limits, restricted chemistry, a minimum Charpy V-notch energy and a defined yield strength range, and the suffix letter states the delivery condition: L360N normalized, L360Q quenched and tempered, L360M thermomechanically rolled or formed.

Chemical Composition

Element PSL 1 L360 or X52 maximum, % PSL 2 L360N, L360Q, L360M maximum, %
Carbon 0.28 seamless, 0.26 welded 0.24
Manganese 1.40 1.40
Phosphorus 0.030 0.025
Sulphur 0.030 0.015
Vanadium Not specified 0.10
Niobium Not specified 0.05
Titanium Not specified 0.04

Vanadium, niobium and titanium are the microalloying elements that allow the PSL 2 grade to reach 360 MPa through grain refinement rather than through carbon content, which is what preserves toughness and weldability. In addition, pipeline specifications frequently tighten the limits further, for example sulphur to 0.010 % maximum and phosphorus to 0.020 % maximum, and set a maximum carbon equivalent of 0.45 % for low temperature or wet service. Carbon equivalent is a calculated value combining carbon and manganese with the alloying and residual elements, and it is the parameter that governs preheat and the risk of hydrogen assisted cold cracking in girth welds.

Mechanical Properties

Property PSL 1 L360 or X52 PSL 2 L360N, L360Q, L360M
Yield strength 360 MPa minimum 360 to 530 MPa
Tensile strength 460 MPa minimum 460 to 760 MPa

Yield strength is measured by the 0.5 % total extension under load method, and PSL 2 pipe is subject to a minimum absorbed Charpy V-notch energy determined on transverse body specimens at a test temperature agreed at the time of ordering. The normalized, quenched and tempered and thermomechanically rolled conditions give different combinations of strength, toughness and microstructure; the M condition, for example, is not intended to receive post weld heat treatment or hot forming after delivery, because that would destroy the benefits of controlled rolling.

Applications and Selection Notes

Onshore and offshore oil and gas transmission and gathering lines of moderate to high pressure.

Water, slurry, carbon dioxide and multiphase transport lines where a thinner wall is an economic advantage.

Station piping, manifolds and riser sections in processing plants.

Structural and piling applications where a certified line pipe grade with documented impact toughness is demanded.

When ordering L360 it is worth confirming three items: the required impact test temperature and energy, the maximum carbon equivalent, and the dimensional tolerances for outside diameter, wall thickness, ovality and straightness. Those three items decide whether the pipe can be welded, coated and laid with the equipment available on the project.

FAQ

Q: Is L360 the same as X52?
Yes. L360 is the metric grade in ISO 3183 and GB/T 9711 and X52 is the equivalent designation in the API 5L imperial table; both state a minimum yield strength of 360 MPa or 52 ksi.

Q: What are the minimum strength requirements for L360 line pipe?
PSL 1 pipe requires a minimum yield strength of 360 MPa and a minimum tensile strength of 460 MPa. PSL 2 pipe must fall within a yield strength range of 360 to 530 MPa and a tensile strength range of 460 to 760 MPa.

Q: What is the difference between PSL 1 and PSL 2 for L360?
PSL 2 adds carbon equivalent limits, restricted carbon, phosphorus and sulphur, mandatory Charpy V-notch impact testing and a defined yield strength range, while PSL 1 covers the basic chemistry and tensile requirements.

Q: What do the letters N, Q and M mean after L360?
They indicate the delivery condition of a PSL 2 pipe: N is normalized or normalizing rolled, Q is quenched and tempered, and M is thermomechanically rolled or thermomechanically formed.

Q: Why is carbon equivalent controlled in L360 pipe?
Carbon equivalent expresses the combined hardening effect of carbon, manganese and the alloying elements, and a high value increases the risk of cold cracking in girth welds. Controlling it at a low level allows field welding with simple preheat practice.

Q: What sizes of L360 line pipe are produced?
Seamless and welded pipe is produced over a wide range of outside diameters and wall thicknesses in schedules and standard weight series, in random or fixed lengths up to about 12 m, with plain, beveled or threaded ends.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry