Oct 15, 2024 Leave a message

Steel Tube Forming Technology for Automobile Chassis Parts

What Automotive Tube Forming Actually Covers

In automotive supply chains, "pipe forming" rarely means making the pipe. It means the operations that convert a purchased tube into a chassis, powertrain or fluid-handling component: cold drawing and cold rolling of the tube itself, high-frequency electric resistance welding of strip into tube, roll forming of open and closed sections, rotary draw bending, end forming by expanding, necking and spinning, and finally tube hydroforming with internal pressure. Each operation changes the local wall thickness and the local strain history, and that strain history is what determines whether the finished part survives a durability test.

A useful reference case is the torsion beam of a rear suspension. The beam is a chassis component whose centre section carries a V-shaped profile, and it is twisted continuously as the left and right wheels move out of phase. Its design driver is therefore torsional fatigue, not static strength. Published forming studies on such beams start from a tube of roughly 101.6 mm outside diameter and 3.4 mm wall thickness with a tensile strength near 752 MPa, press-form the blank into the beam shape, and then apply internal pressure together with axial feed to calibrate the final geometry. The finding that matters for buyers is simple: the residual stress left behind by forming reduces fatigue life, and a forming route that leaves a more uniform strain distribution leaves less residual stress behind. Forming technology is therefore a fatigue specification, not only a shape specification.

Residual stress appears because deformation is not uniform. In a bent tube the outer fibre stretches and the inner fibre compresses; in a hydroformed corner the wall thins locally while the adjacent flat stays nearly undeformed; in a cold-drawn tube the outer surface is deformed more heavily than the mid-wall. Because these gradients are locked in by the surrounding material, they remain in the part as a self-equilibrating stress field. When that field is superimposed on service load, the local mean stress rises, the fatigue limit falls, and springback and dimensional drift appear after any later cutting or welding.

Tube Families in a Vehicle and What Each One Demands

Automotive tube is not a single product. Six families dominate, and they are bought against different standards, different tolerances and different forming routes. Confusing one family with another is the most common sourcing error in this segment.

Tube family Typical specification Typical size range Dominant forming and finishing route
Structural and body tube ASTM A513, EN 10305-3, EN 10219-2 20 mm to 120 mm OD, 1.2 mm to 5.0 mm wall ERW then cold sizing, roll forming, hydroforming, bending
Driveshaft and propeller shaft tube ASTM A513 Type 5, EN 10305-1 50 mm to 120 mm OD, 1.5 mm to 4.0 mm wall DOM drawing to remove the weld bead, straightening, balance control
Exhaust system tube ASTM A554, EN 10305-2, EN 10217-7 25 mm to 90 mm OD, 1.0 mm to 2.5 mm wall Welded ferritic or austenitic stainless, mandrel bending, end expansion
Shock absorber and damper tube EN 10305-1 E235 or E355, DIN 2391-1 25 mm to 70 mm OD, 1.0 mm to 3.0 mm wall Cold drawing, honing or skiving and roller burnishing of the bore
Steering column and seat frame tube JIS G3445 STKM series, EN 10305-2 25 mm to 60 mm OD, 1.2 mm to 3.0 mm wall Cold drawn welded tube, swaging, flattening, collapse features
Fuel, brake and hydraulic line tube ASTM A254, EN 10305-4, ISO 3304 and ISO 3305 4.76 mm to 12 mm OD, 0.6 mm to 1.2 mm wall Copper-brazed double wall or seamless cold drawn, zinc or Zn-Ni coating, coil winding

Each family has a different critical dimension. For a damper tube the bore diameter and bore finish govern, because the piston seal runs on it. For a driveshaft the wall thickness distribution and the residual imbalance govern, because whirl and critical speed depend on them. For a brake line the wall integrity and coating adhesion govern, because a pinhole is a safety defect. For a hydroformed body node the wall thickness map after forming governs, because crash and stiffness analysis is run on that map. Buying all six families against one generic "steel tube" description guarantees mismatch.

Base Materials and Grades Used in Formed Tube

The grade system for automotive tube is layered. There is a European precision-tube system built on EN 10305, a legacy German system still written into many drawings as DIN 2391, a Japanese system built on JIS G3445, and an American system built on ASTM A513 for mechanical tubing. They overlap but are not interchangeable.

EN 10305 is organised by product form rather than by application: part 1 covers seamless cold-drawn tube, part 2 welded cold-drawn tube, part 3 welded cold-sized tube, and part 4 seamless cold-drawn tube for hydraulic and pneumatic power systems. The grade names are minimum-yield labels: E235 guarantees 235 MPa minimum yield, E275 guarantees 275 MPa, E355 guarantees 355 MPa. The letter E marks it as an engineering steel grade. What the grade name does not tell you is the delivery condition, and the delivery condition changes the properties more than the grade does.

DIN 2391-1 and 2391-2 remain on a large number of older drawings as St35, St45 and St52. These map closely onto E235, E275 and E355 respectively, and a supplier working to EN 10305-1 can normally certify against the older designation as well, but the request has to be made explicitly because the tolerance tables in the two documents are not identical. St35 is the general-purpose cold-drawn grade, St45 is used where a higher strength is needed without changing the forming route, and St52 is used for higher-pressure and higher-load parts where its lower elongation is acceptable.

JIS G3445 covers carbon steel tubes for machine structural purposes and is the backbone of Japanese-derived chassis and seat hardware drawings. Its grades run as STKM 11A through the higher numbers, with a letter suffix A, B or C. The numeric part of the designation steps up in strength, and the letter suffix marks progressively higher carbon content, which raises strength and hardness but reduces the elongation available for bending and flaring. A part designed around an A suffix grade frequently cracks when a purchasing change substitutes a C suffix grade of the same number, because the forming ductility is not the same.

ASTM A513 is the American mechanical tubing standard and is organised by type rather than by grade. Type 1 is cold-rolled electric resistance welded carbon tube, Type 2 is hot-rolled electric resistance welded, Type 5 is drawn over mandrel, which removes the inside weld bead and delivers the tightest concentricity, and Type 6 is cold-drawn alloy tube. The chemistry is called out with AISI and SAE designations such as 1010, 1020, 1026 and 4130, and the tensile requirement depends on the type, the size and the chemistry, so the certificate has to be read against the correct table rather than assumed.

Grade or designation Standard Delivery condition Minimum yield strength Tensile strength Minimum elongation
E235 EN 10305-1 Cold drawn, normalized +N 235 MPa 370 to 490 MPa 25 percent
E355 EN 10305-1 Cold drawn, normalized +N 355 MPa 490 to 630 MPa 22 percent
E235 cold drawn +C EN 10305-1 As drawn, no final anneal Not fixed by grade Typically 100 to 150 MPa above the +N value Reduced, order-specific
St35 / St45 / St52 DIN 2391-1 and 2391-2 Cold drawn, various finishes Mapped to E235 / E275 / E355 Per the standard tables Per the standard tables
STKM 11A to 20A JIS G3445 As drawn or annealed Steps up across the series Steps up across the series Falls as the suffix moves from A to C
1020, Type 5 DOM ASTM A513 Cold drawn over mandrel Chemistry-based Per the A513 table for type and size Per the A513 table
4130, Type 6 ASTM A513 Cold drawn alloy Chemistry-based Substantially above the carbon types Low, heat treatment normally follows
DP590 and DP780 EN 10346 and VDA 239-100 practice As supplied, dual phase Below the tensile label 590 MPa and 780 MPa minimum High uniform elongation relative to strength

Two points in that table need emphasis. First, the dual-phase designations DP590 and DP780 label minimum tensile strength, not yield strength; a buyer who reads them as yield values will over-design the part and then find that the actual yield is far lower. Second, a cold-drawn tube sold only as "E235" without a condition suffix is ambiguous, because +C, +LC, +SR, +A and +N produce very different elongation and residual stress states from the same chemistry.

For exhaust systems the material question changes entirely: corrosion, not strength, selects the grade. Ferritic stainless steels in the 409, 439 and 441 families and welded austenitic tube to ASTM A554 dominate, with aluminium-silicon coated carbon steel used on the cooler downstream sections. Those grades are formed by bending and end expansion, so elongation and coating adhesion matter more than yield strength.

Cold Drawing and Cold Rolling: Precision Through Deformation

Cold drawing is the route to dimensional precision. A hollow shell, either seamless or welded and descaled, is pulled through a die over a mandrel or a plug, or without an internal tool in the case of sinking. Each pass reduces the section, and the tooling geometry decides whether the outside diameter, the wall or both are controlled.

Three variants matter commercially. Mandrel drawing controls both outside diameter and wall simultaneously, produces the best concentricity and the smoothest bore, and is the route used for damper tube, hydraulic cylinder tube and DOM driveshaft tube. Plug drawing fixes the outside diameter and thins the wall against a fixed plug, which is cheaper per pass but gives less control of wall eccentricity. Sinking reduces the outside diameter with no internal support, thickening the wall slightly and leaving the bore rougher; it is used for intermediate passes and for low-cost structural tube.

Reduction per pass is normally held in the range of roughly 15 to 30 percent of area for mandrel drawing, with interpass annealing inserted whenever the accumulated cold work would exhaust the remaining ductility. The number of passes is therefore a cost driver that a buyer can read directly from the process route: a two-pass tube and a five-pass tube can share the same final size and the same certificate grade while behaving differently in a subsequent flare or hydroform, because the retained cold work and the residual stress pattern differ.

Cold rolling, using a pilger mill, deforms the wall by a reciprocating roll pass rather than by pulling. It suits heavy walls and large reductions, gives excellent wall uniformity and a characteristic surface, and is preferred where wall thickness is the governing dimension. It is slower than drawing, so it is used selectively.

The metallurgical consequence of both routes is work hardening: yield and tensile strength rise, elongation and strain hardening capacity fall, and residual stress accumulates. A cold-drawn E235 in the +C condition can be substantially stronger than the same grade in the +N condition, which is why some drawings deliberately specify +C for strength and accept the ductility penalty. When the part will be bent, flared or hydroformed, the drawing must specify the annealed or stress-relieved condition instead, or a subsequent forming operation will fail.

ERW High-Frequency Welding and Roll Forming

Most automotive tube starts as slit strip that is progressively formed into a circular section and then welded along the seam. In high-frequency electric resistance welding, the strip edges are brought together and heated by induction coils or contact electrodes in the range of roughly 100 to 500 kHz, and the edges are forged together by squeeze rolls. An impeder inside the tube concentrates the current at the seam. The weld is then scarfed on the outside, and on the inside where the application requires it.

Weld quality is decided by a small number of variables: edge preparation and strip camber, the included angle of the V at the weld point, the amount of up-set or squeeze, the power input, and the speed. Too little heat gives a cold weld with incomplete fusion; too much heat produces a coarse cast zone, spatter and a thick internal bead. Both are detectable but neither is visible on the finished surface, which is why weld-seam inspection has to be a specified, instrumented operation rather than a visual one.

After welding, the tube passes through sizing and straightening stands. For carbon steel tube used in bending or hydroforming, the weld zone is often normalised in line by an induction coil to refine the cast structure and reduce the hardness peak, and the resulting hardness traverse across the seam is a legitimate acceptance criterion.

Roll forming is the other major forming family. Strip is passed through a series of profiled roll stands, each adding a small bend, until an open section or a closed section is produced. Automotive applications include door impact beams, bumper reinforcements, seat rails, roof bows and the shells that are subsequently closed by welding. Roll forming is economical at long run lengths and can combine several operations in line: punching, notching, local embossing and cut-off. Its weaknesses are springback, which must be compensated in the roll design, and the residual longitudinal strain that appears when a wide strip is formed into a deep section, which can bow the finished part.

A variant that has grown quickly is the roll-formed closed section produced from a single strip, seam-welded and then hydroformed or swept. It competes directly with welded tube where the section is not circular, because it avoids the cost of a dedicated tube mill run.

Bending, Sizing, Expanding, Necking and Spinning

Bending is the most common secondary operation and the one that most often causes a rejection. In rotary draw bending, the tube is clamped against a bend die and pulled around it while a pressure die supports the outside and a mandrel, often with a series of balls, supports the inside. The result depends on the ratio of centreline radius to outside diameter, the ratio of diameter to wall thickness, the mandrel type and the lubrication.

Practical limits are worth stating in specification terms rather than adjectives. A centreline radius below about two times the outside diameter is a tight bend that needs a full mandrel and usually a boost or a reduced wall; severe thinning on the outer fibre and wrinkling on the inner fibre are the failure modes. Ovality across the bend is commonly capped at 5 to 10 percent of the nominal diameter for chassis and exhaust parts, and wall thinning at the outer fibre is commonly capped near 15 percent, with tighter limits where fatigue is the design driver. Springback must be compensated by over-bending, and because springback varies with yield strength and with the cold-work state, a change of delivery condition from +N to +C will change the bend angle unless the tooling is adjusted.

For large radii and for thick walls, three-roll bending and induction bending are used. Induction bending heats a narrow band while the tube is pushed through a pivot arm, producing a tight radius with limited ovality and limited need for a mandrel, at the cost of a heat-affected zone that must be considered in the fatigue assessment.

End forming covers expanding, necking and spinning. Expanding opens the tube end to receive a hose or a joint and is checked by a drift-expanding test. Necking or swaging reduces the end to enter a bore or to accept a press-fit connection, and is usually done in several stages with interstage annealing for thin walls. Spinning forms tapers, flares and rolled beads by pressing a roller against a rotating tube end. All three operations concentrate strain at the transition, so the transition radius and the local wall thickness after forming are the dimensions to specify and measure.

Hydroforming: Internal Pressure Combined With Axial Feed

Tube hydroforming places a pre-bent or pre-crushed tube in a closed die, seals both ends with axial rams, fills the cavity with emulsion, and applies internal pressure while the rams push material into the die. The tube expands until it conforms to the die surface. Internal pressure is typically in the range of 40 to 120 MPa, and calibration of tight corners and small radii in high-strength grades can require substantially more.

The sequence is usually pre-bend, pre-form by crushing to fit the die cavity, closure, filling, axial feed, pressurisation and calibration, then decompression and extraction. The axial feed is what makes the process viable: without it, expansion is limited to the elongation of the base material, and the wall thins until it bursts. With a correctly tuned feed and pressure curve, material flows from the ends into the expanding regions and the thickness distribution can be controlled within a planned map rather than left to chance.

The advantages are structural. A hydroformed node replaces several stamped parts and their welds, so stiffness per unit mass improves and the number of joints that need fatigue qualification falls. Sections that are not circular become possible, so a member can be deep where bending stiffness is needed and shallow where package space is limited. Dimensional repeatability is good because the die defines the final surface. Work hardening during forming raises local strength, which is why hydroformed parts often show higher measured strength in the calibrated corners than the incoming tube certificate suggests.

The limits are equally specific. The incoming tube needs high elongation and a low yield-to-tensile ratio, uniform properties along the length and around the circumference, a tight wall tolerance and a controlled weld seam. A seam placed on the outer fibre of a sharp corner is a crack initiator. Lubrication and the surface condition of the tube govern friction, and friction governs whether material flows or thins.

Residual stress control is where the process design connects back to fatigue. Because the stress field left after forming follows the strain distribution, a pressure and feed schedule that equalises strain around the circumference leaves a lower and more uniform residual stress, and the resulting part performs better in torsional and bending fatigue. This is the mechanism behind the torsion beam case described earlier: the V-shaped centre section is formed, then calibrated under internal pressure with axial feed, and the fatigue resistance improves because the forming stress field becomes more uniform. Where the geometry still leaves a steep gradient, a post-forming stress relief anneal at a moderate temperature is the conventional remedy, provided the grade and the coating can tolerate it.

Dimensional Accuracy and Tolerance Stack-Up

Precision tube is bought on tolerances, not on nominal size. The tolerances that matter for forming are outside diameter, wall thickness, wall eccentricity, concentricity between bore and outside surface, straightness, length and cut squareness. A tube that meets a loose wall tolerance and a loose straightness tolerance can still be impossible to feed into an automated bender.

Characteristic Typical order value for formed automotive tube Reference or verification method
Outside diameter Plus or minus 0.10 mm on small sizes, plus or minus 0.15 mm above about 50 mm EN 10305-1 tables, ISO 3304 and ISO 3305; micrometer at three positions per end
Wall thickness Plus or minus 10 percent, with a floor on the absolute value Ultrasonic wall gauge at four circumferential positions per end
Wall eccentricity 10 percent of nominal wall or better for hydroforming stock Wall gauge survey, wall map recorded on the certificate
Bore diameter for damper and cylinder tube H8, H9 or H10 depending on the seal system Air gauge or bore micrometer, taper and roundness included
Concentricity 0.05 to 0.10 mm total indicator reading Rotating fixture with a dial indicator on the outside while the bore is supported
Straightness 0.5 to 1.0 mm per metre, with a total length limit Surface plate and feeler gauge, or laser alignment
Cut length Plus or minus 1 mm for cut-to-length bender feed stock Tape or laser measurement on a sample basis
Cut end squareness 0.5 mm maximum deviation across the end Square and feeler gauge; burr height checked at the same time
Ovality after bending 5 to 10 percent of nominal diameter, application dependent Sectioning or a ball gauge through the bend

Two tolerance interactions deserve attention. The first is that wall tolerance and wall eccentricity are different things: a tube can be within plus or minus 10 percent on average wall while one side is thin enough to burst early during hydroforming. For hydroforming stock, the specification has to limit eccentricity explicitly. The second is the stack-up between tube tolerance and tooling: an automated bender that is set for a nominal diameter will produce angle errors if the incoming tube sits at the top of the diameter tolerance, because the clamp and the pressure die no longer close on the same geometry. That is why formed-part programs usually buy tube to a narrower band than the standard allows and treat the standard tables as a starting point rather than a specification.

Mechanical and Technological Properties to Specify

Mechanical properties are the first thing buyers ask for and the least sufficient. A tensile test result tells you the strength and the elongation in the longitudinal direction at room temperature, on a specimen that may be a full section or a strip cut from the wall. It does not tell you whether the tube will survive a tight bend, a flare or a hydroform.

The tensile test is performed to ISO 6892-1. Yield is reported as the upper yield strength ReH for low-carbon grades with a distinct yield point, or as the 0.2 percent proof strength Rp0.2 where the transition is gradual, which is the normal case for cold-worked and dual-phase material. Elongation is reported as a percentage on a stated gauge length, and the gauge length must be stated on the certificate or the number is not comparable. Hardness is measured to ISO 6507 for Vickers or ISO 6508 for Rockwell, and is useful mainly as a check for decarburisation, weld-zone hardening and unintended cold work.

The technological tests are the ones that actually predict forming behaviour, and each targets a different operation:

Flattening to ISO 8492 compresses a tube section between flat platens until the wall reaches a specified separation. It reveals circumferential ductility and, when applied to welded tube with the weld at the point of maximum bend, it reveals weld ductility. Bend testing to ISO 8491 wraps a tube around a mandrel of stated radius; mandrel bending over 90 or 180 degrees with the weld on the outside of the bend is the classical weld-quality check. Drift expanding to ISO 8493 drives a tapered mandrel into the tube end and measures the expansion achieved before cracking, which predicts how the part will behave in a hose-end expansion. Flanging to ISO 8494 rolls a flange at the tube end and is used for parts that carry a bolted connection. Ring expanding to ISO 8495 and ring tensile to ISO 8496 test the transverse properties of the wall.

For hydroforming and severe bending, three additional parameters are worth writing into the purchase specification: the yield-to-tensile ratio, which should be low so that the material has reserve before it necks; the uniform elongation, which is the strain the material can carry before localisation; and the strain hardening exponent, which describes how quickly strength builds with strain. A steel with a high tensile strength but a high yield-to-tensile ratio and low uniform elongation will burst in a hydroform die even though it passes the tensile test with a comfortable margin.

Dimensional stability after machining is also a property issue. Cold-drawn tube carries residual stress, and if a ring is machined from one end the balance of that stress is disturbed and the ring goes out of round. Where a customer machines the tube after delivery, the tube should be ordered in a stress-relieved condition and the relief should be stated on the drawing.

Heat Treatment and Surface Condition

Delivery condition suffixes on an EN 10305 order are not administrative. They describe the thermal history and therefore the forming behaviour of the tube.

+C is as cold drawn, with no final heat treatment. Strength and hardness are at their highest for a given reduction, elongation is at its lowest and residual stress is at its highest. It suits parts that are cut and machined but not formed.

+LC is a light anneal, sufficient to relieve most of the forming stress without fully recrystallising the structure. Strength drops moderately and ductility recovers enough for moderate bending.

+SR is a stress relief anneal, typically in the range of roughly 480 to 650 degrees Celsius followed by slow cooling. Its purpose is to remove residual stress while retaining most of the cold-work strength, which is exactly the combination needed for a part that must hold a machined dimension but has already been formed.

+A is a soft anneal, a full recrystallisation anneal, usually in the range of roughly 650 to 720 degrees Celsius for low-carbon grades. It gives the highest ductility and the lowest strength, and is the condition to specify when the tube will be severely bent, end-formed or hydroformed.

+N is normalising, typically in the range of roughly 880 to 930 degrees Celsius, producing a fine ferrite-pearlite structure with properties close to the grade's specified minimums. It is the reference condition for mechanical property tables.

For annealed tube the atmosphere matters as much as the temperature. Bright annealing in a nitrogen-hydrogen atmosphere leaves a scale-free, oxide-free surface that needs no further cleaning and is essential for hydraulic and damper tube, where scale would damage seals and contaminate the circuit. Controlled atmosphere also avoids decarburisation, which would otherwise soften the surface layer and reduce fatigue resistance.

Surface treatment has three distinct purposes and they are frequently confused:

Forming lubrication carriers. Phosphating to ISO 9717 produces a crystalline conversion coating that holds drawing soap and reduces friction in cold drawing and in hydroforming. The coating weight and crystal structure are process variables, and a coating specified only as "phosphated" is under-specified.

Corrosion protection. Electroplated zinc to ISO 2081 or ASTM B633, zinc-nickel for brake and fuel lines that see road salt, hot-dip galvanising to ISO 1461 or ASTM A123 for heavier structural parts, and zinc-aluminium coatings applied to the strip before tube forming for exhaust and underbody parts. Coating thickness, adhesion after forming and coverage on sheared ends are the acceptance points. A coating that survives flat-panel salt spray but fails after a 90 degree bend has not been qualified for the application.

Cleanliness. Hydraulic and fuel-system tube is specified for internal cleanliness, often using ISO 16232 particle count limits, because residual drawing lubricant, phosphate dust or metal fines will migrate to a valve or an injector. Cleanliness is measured on a flush sample, and the extraction method has to be agreed because different methods give different counts.

Weld Seam Quality and Non-Destructive Testing

For welded tube the seam is the weakest link in fatigue and in hydroforming, and it is invisible from the outside. Weld quality has to be specified as measurable attributes rather than as a general requirement.

The attributes that matter are weld penetration and fusion through the full wall, absence of cold welds and stitch defects, absence of oxide or penetrator inclusions at the fusion line, control of the internal bead height, and control of the external scarf so that no burr remains above an agreed limit. For drawn-over-mandrel tube the internal bead is removed entirely by the drawing operation, which is one reason DOM tube is preferred for driveshafts and for hydroforming stock. For tube that is not drawn, the internal bead is a stress raiser and a flow obstruction, and a bead height limit of a few tenths of a millimetre is normal for hydraulic service.

Non-destructive testing for automotive tube draws on the ISO 10893 series, which covers the individual methods and the acceptance levels:

Eddy current testing to ISO 10893-2 is the standard full-body test for welded and seamless tube. It detects longitudinal and transverse discontinuities and is fast enough for in-line use; it is the usual test for a 100 percent scan on small-diameter tube.

Magnetic testing to ISO 10893-5 covers magnetic particle inspection for surface imperfections on ferromagnetic tube, and flux leakage methods to ISO 10893-3 are used where a magnetic rather than an eddy current technique is preferred.

Ultrasonic testing of the weld seam to ISO 10893-11 uses a probe arrangement angled to the seam and detects lack of fusion, cracks and penetrators that eddy current may miss in thick walls. Automated full-periphery ultrasonic testing to ISO 10893-10 covers laminar and volumetric defects over the whole body, and the laminar imperfection method to ISO 10893-8 is used where delamination-type defects are a concern.

Radiographic testing to ISO 10893-6 and ISO 10893-7 is used for reference and for audit rather than for volume production.

Leak and pressure integrity are separate from the discontinuity tests. Hydrostatic testing proves the wall, and a pneumatic leak test proves tightness. For brake and fuel lines, tightness is tested at a multiple of working pressure on every piece or on a defined sampling basis, and burst testing is performed on samples to confirm that the formed and coated tube still meets the design burst requirement after bending and end forming. The acceptance numbers must be taken from the applicable product standard and from the drawing, not selected by the supplier.

Certification is part of the quality specification. An inspection certificate to EN 10204 type 3.1, issued on the basis of actual test results from the delivered lot, is the normal requirement for automotive safety-related tube; a type 2.2 certificate, which is a statement of compliance without test data, is not equivalent and should not be accepted where the part is safety-related.

Lightweighting and High-Strength Steel Trends

Mass reduction in body and chassis structures has moved tube forming in two directions at once: thinner walls in conventional grades, and thicker-section parts in much stronger grades.

The thinner-wall route is the simpler one and it is limited by stiffness and by forming. Reducing wall from 3.4 mm to 2.9 mm in a torsion beam removes about 15 percent of the mass of that member, but torsional stiffness falls faster than mass because stiffness scales with wall thickness while mass scales linearly, and the forming window narrows because the tube is more sensitive to wall eccentricity and to local thinning at the corners. The compensation is a section redesign, which is exactly what hydroforming enables: a deeper or more complex section recovers stiffness that the thinner wall gave up.

The high-strength route uses dual-phase, complex-phase and martensitic steels with minimum tensile strengths from 590 MPa upward, and press-hardened 22MnB5 for parts that are formed hot and quenched in the tool. For tube, dual-phase grades in the DP590 and DP780 class are hydroformed into body nodes and structural members, where their combination of high strength and continuous yielding gives a good strain distribution. Martensitic grades at 1200 MPa and above are more often roll formed into door impact beams and bumper reinforcements, where the part is simple in shape and the requirement is bending resistance.

These materials bring specific manufacturing problems. Springback grows with strength, so tooling compensation becomes a design task rather than a trimming adjustment. The weld heat-affected zone in a welded high-strength tube can soften relative to the base metal, creating a soft band that localises strain during hydroforming. Edge cracks appear at sheared or trimmed edges where the local ductility has been exhausted, so trimming practice has to be specified. And the forming window between the yield point and the point of localised necking narrows, which means that tube tolerance, surface friction and lubrication all become more critical, not less.

Two further trends are worth tracking for specification purposes: tailor-welded tube blanks, where sheets of different thickness or grade are welded before forming so that thickness follows the load path, and variable-thickness roll forming, which produces a continuous thickness transition along the part. Both move the quality burden upstream into the weld and the thickness transition, and both require the tube or blank supplier to declare a thickness map rather than a single nominal wall.

Purchasing Checklist and Common Misconceptions

A formed-tube purchase order that is written only as a size, a grade and a quantity leaves the important variables to the supplier's default, and the default is rarely what the forming process needs. The following items belong on the drawing or the order, because each one changes the outcome of a downstream operation.

Standard and edition, with the product part number where the standard is divided by product form; grade designation including the delivery condition suffix; outside diameter and wall tolerance, stated separately from the nominal size; wall eccentricity limit for hydroforming and honing stock; bore tolerance and bore surface finish for damper and cylinder tube; straightness and cut squareness; the position and treatment of the weld seam, including whether the internal bead is to be removed; the non-destructive test method, the acceptance level and the scan coverage; the mechanical property requirements, including test direction and gauge length; the technological test requirements, such as a flattening or drift-expanding value; surface treatment specification with coating weight and post-forming adhesion requirement; internal cleanliness limit for fluid systems; the inspection certificate type; marking, traceability and bundling, including end caps and interleaving for coated tube.

Alongside that checklist, several misconceptions recur often enough to be worth naming:

"Cold drawn is always better." Cold drawing gives precision, not unconditional quality. The same grade in a heavily cold-worked condition has high strength, low elongation and high residual stress, and will crack in a flare or a hydroform where an annealed tube of the same grade succeeds.

"The grade name fixes the properties." E235 in the +C condition and E235 in the +N condition are the same grade and behave very differently. The condition must be on the order.

"Any welded tube can be hydroformed." Hydroforming needs high uniform elongation, low yield-to-tensile ratio, controlled wall eccentricity, a clean and fully fused seam and a seam position that avoids the outer fibre of sharp corners. A general-purpose ERW tube rarely satisfies all of these.

"Tolerance is symmetrical, so the middle of the band is safe." A wall at the bottom of a plus or minus 10 percent band reduces burst pressure disproportionately, because burst pressure scales with wall thickness and with strength together. Programs that push mass reduction tend to buy the tolerance band deliberately narrowed.

"Coating is a paint question." For a formed part, coating adhesion after bending and after end expansion is the real criterion. Salt spray results on flat panels say very little about a coated tube that will be bent to a two-diameter radius and flared at the end.

"Residual stress is a forming shop problem." Residual stress is created by the forming route and by the delivery condition of the tube, and it shows up as dimensional drift after machining, as springback variation in bending and as reduced fatigue life. It is a specification item for the tube buyer, not only for the forming engineer.

FAQ

Q: What is the difference between EN 10305-1 and DIN 2391 for cold-drawn tube?
EN 10305-1 is the current European standard for seamless cold-drawn tube and uses the E-series grade names E215, E235, E275 and E355 with delivery condition suffixes. DIN 2391-1 and 2391-2 are the earlier German standards using St35, St45 and St52, which correspond broadly to E235, E275 and E355. The grades overlap, but the tolerance tables and the condition designations are not identical, so a drawing that cites DIN 2391 should state the tolerance class and the condition explicitly rather than relying on a nominal equivalence.

Q: Which delivery condition should be ordered for tube that will be hydroformed?
Soft annealed +A or, at minimum, a light annealed +LC condition, because the process needs high uniform elongation and a low yield-to-tensile ratio so that material can flow into the expanding corners without localised necking. As-drawn +C tube is unsuitable for anything beyond a shallow calibration pass, since the remaining ductility is small and the residual stress from drawing adds to the forming stress.

Q: Why does a welded tube crack at the weld seam during bending even though the tensile test passes?
A longitudinal tensile test samples the base metal and says nothing about the weld. The seam can contain a cold weld, an oxide inclusion at the fusion line, an unfused zone or a hardness peak, all of which reduce local ductility. The relevant checks are a flattening test with the weld at the point of maximum bend, a mandrel bend test with the weld on the outer fibre, a hardness traverse across the seam, and ultrasonic testing of the seam to ISO 10893-11.

Q: How much wall thinning is acceptable at the outer fibre of a bent tube?
It depends on the design case, but a common acceptance limit for chassis and exhaust tube is around 15 percent of nominal wall at the outer fibre, together with an ovality limit of 5 to 10 percent of nominal diameter. Where fatigue or pressure containment is the governing case, both limits should be tightened and verified by sectioning the first-off part rather than assumed from the tooling design.

Q: What does the Type number mean in ASTM A513 tube?
The type describes how the tube is made rather than what it is made of. Type 1 is cold-rolled electric resistance welded carbon tube, Type 2 is hot-rolled electric resistance welded, Type 5 is drawn over mandrel with the inside weld bead removed, and Type 6 is cold-drawn alloy tube. The chemistry is called out separately using AISI and SAE designations, and the tensile requirement is read from the table that applies to that type and size.

Q: Is a 3.1 certificate necessary for automotive tube?
For safety-related parts such as brake lines, steering components, suspension members and damper tube, an inspection certificate to EN 10204 type 3.1 with actual test results from the delivered lot is the normal expectation. A type 2.2 certificate only confirms compliance with the order without reporting test data, so it cannot support a part qualification or a traceability audit on its own.

Q: Why does a cold-drawn tube move out of round after a ring is machined from it?
Machining removes material that was carrying part of the locked-in residual stress field, so the remaining stress redistributes and the ring distorts. The remedy is to order the tube in a stress-relieved +SR or annealed +A condition, or to specify a stress relief operation after rough machining and before finish machining.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry