Mar 29, 2024 Leave a message

20Cr Alloy Seamless Pipe: Composition, Properties and Uses

What 20Cr Seamless Tube Is and Where It Belongs

20Cr is an alloy structural steel defined by GB/T 3077, with a nominal carbon content of 0.20 % and about 0.85 % chromium. It is a carburising grade: the low carbon core keeps toughness and machining behaviour, while the surface can be enriched with carbon and hardened to carry contact load. Seamless tube in 20Cr is used where a hollow section must transmit torque or carry a loaded shaft function and the surface must resist wear, so the material is chosen for hardenability and case response rather than for pressure containment.

This is the first point a buyer must be clear about. 20Cr is not a line pipe grade, not a boiler grade and not listed in API SPEC 5L or in ASME BPVC Section II Part A. The chemistry is set by GB/T 3077, the dimensional tolerances of the tube come from GB/T 17395, and the mechanical properties follow the bar product standard unless a separate tube specification is agreed. Orders that describe 20Cr tube as pipe for conveying oil or natural gas are mixing two product families, and the mill certificate will not support that duty.

Chemical Composition and Heat Analysis Limits

GB/T 3077 sets the heat analysis limits for 20Cr. Chromium at 0.70 % to 1.00 % provides hardenability, manganese at 0.50 % to 0.80 % assists it, and silicon at 0.17 % to 0.37 % is a residual deoxidation element. Residual copper and nickel are capped to protect forgeability, and both phosphorus and sulfur are held low because the grade is normally machined and carburised after delivery. Product analysis tolerances from the ladle to the finished tube are governed by GB/T 222.

Element Heat analysis, % Function in the grade
C 0.18-0.24 Low core carbon for toughness, carburised case for wear
Si 0.17-0.37 Deoxidation, ferrite strengthening
Mn 0.50-0.80 Hardenability, sulfur control
Cr 0.70-1.00 Principal hardenability element, carbide former
P 0.030 max Tramp element, controlled for toughness
S 0.030 max Tramp element, controlled for hot ductility
Cu 0.30 max Residual ceiling
Ni 0.30 max Residual ceiling

Chromium is the element worth checking on the certificate. A heat near 0.70 % behaves noticeably differently from one near 1.00 % in the Jominy curve and in the achievable case-to-core hardness gradient, which is why hardenability-controlled supply to GB/T 5216 with a declared hardenability band is common for gear and shaft work, while GB/T 3077 alone only guarantees composition and tensile properties.

Mechanical Properties in the Delivered Condition

GB/T 3077 specifies the tensile properties of 20Cr in the quenched and tempered condition, with the annealed hardness ceiling used for machinability. These figures describe the supplied tube, not the carburised surface, and they are the values a purchaser should see on the incoming certificate before any heat treatment is applied by the fabricator.

Property Requirement Test basis
Tensile strength Rm 835 MPa minimum Tensile test on quenched and tempered specimen
Yield strength ReL 540 MPa minimum Same specimen, gauge length 50 mm
Elongation after fracture A 10 % minimum Proportional specimen
Reduction of area Z 40 % minimum Measured at fracture
Impact energy KU2 47 J minimum Charpy V-notch, specimen size declared on certificate
Hardness, annealed or high temperature tempered 179 HBW maximum Brinell, for machining condition

The impact figure requires reading the specimen size. A 47 J result on a 10 mm by 10 mm specimen is not comparable with the same energy on a 5 mm subsize specimen taken from a thin wall, and thin-wall tube is exactly where subsize testing is common. The certificate must state the subsize used, otherwise the toughness statement cannot be compared across suppliers. Equally, the 10 % elongation is a bar property and looks low next to pipe grades, because the grade is designed for a hardened case rather than for bending and field welding of a pressure boundary.

Carburising Behaviour and Case Depth Selection

The service performance of a 20Cr component is created in heat treatment, not in the mill. Typical practice carburises at 900 C to 930 C in a gas atmosphere to a surface carbon of roughly 0.8 % to 1.0 %, followed by direct quenching or re-heating and quenching in oil, then tempering between 150 C and 200 C. The result is a case of 58 HRC to 62 HRC over a tougher core, and the residual austenite level in the case must be controlled or the surface will lose hardness in service.

Case depth is a design decision that must be written on the drawing. As a working rule, effective case depth for gears and shafts falls in the 0.5 mm to 1.5 mm band depending on module or section, with the depth measured to a defined hardness such as 550 HV. Too shallow a case collapses under contact pressure and spalls; too deep a case leaves an abrupt transition and risks case crushing. Because 20Cr has moderate hardenability compared with manganese-chromium carburising grades, section size matters: thick sections may not through-harden at the core, which limits the grade in heavy tube walls.

Distortion is the practical penalty of carburising a long hollow section. Seamless tube in 20Cr is often straightened after heat treatment, and the permitted straightness and the allowance for grinding stock must be agreed before the order, since a carburised and hardened tube cannot be straightened cold without cracking risk.

Cold Drawing, Machining and Dimensional Control

20Cr seamless tube is normally supplied hot rolled and then cold drawn to the final size, either to a mandrel or to a plug, followed by annealing to the 179 HBW maximum for machining. Cold drawing gives the concentricity and bore finish required for ring-shaped parts, bushings and sleeves that are machined all over. Tolerances are taken from GB/T 17395 for outside diameter and wall, with tighter classes available by agreement, and the bore finish is specified when the inside surface is functional.

Machinability of the annealed grade is good but not free-cutting. Machining parameters should assume a soft, gummy chip rather than the brittle chip of a resulfurised grade, and the absence of lead or sulfur addition makes 20Cr a sensible choice where the finished part must also be welded. Where high-volume turning dominates the cost, a resulfurised alternative may be cheaper to machine but must be excluded from any carburised, highly stressed surface.

Welding, Fabrication and Post-Weld Treatment

20Cr is weldable with care but it is not a pipe steel, and welding procedure qualification is expected rather than optional. The chromium and carbon combination raises hardenability, so the heat affected zone can form untempered martensite and crack under restraint. Preheat in the 150 C to 250 C range for sections above roughly 20 mm, low-hydrogen consumables, controlled interpass temperature and a post-weld temper are the usual controls, with the exact parameters established by procedure qualification testing.

Two fabrication rules follow. First, avoid welding on a carburised or hardened surface; the case will crack, and any weld should be completed before final heat treatment. Second, do not use 20Cr tube for site-run piping that must be bent and welded in the field, because the grade has no low-temperature impact qualification for that duty and no acceptance route in a piping code. For fluid transfer, a GB/T 8163 or API 5L grade is the correct material; for mechanical parts, 20Cr is the correct material.

Applications That Match the Grade

Carburised 20Cr is used for gears, worm shafts, splined shafts, piston pins, camshafts for small engines, sleeves, bushings, chain pins and lightly loaded bearing rings, as well as for jigs, fixtures and gauges where surface wear matters and the part must be machined to shape. Hollow sections suit ring-shaped components because the bore eliminates the rough machining of a solid bar, which is the main cost saving offered by tube over bar stock.

Where core strength beyond 835 MPa tensile is needed, or where the section is too thick for 20Cr to through-harden, the next step is a manganese-chromium carburising grade or a nickel-chromium-molybdenum grade with better hardenability. Where corrosion resistance is required, no carburised carbon or low-alloy steel is suitable and a stainless or surface-coated route replaces it. Sizing the grade against the section and the duty is more valuable than specifying a higher strength number.

Inspection, Documentation and Acceptance

An incoming inspection for 20Cr seamless tube should cover four items. Verify the EN 10204 3.1 certificate against the order: grade, heat number, heat analysis and mechanical results, with the impact specimen size stated. Confirm the delivered condition is annealed and within the hardness ceiling. Check dimensions to GB/T 17395 on outside diameter, wall thickness at multiple points, length and straightness. Finally, confirm identity by positive material identification with a handheld X-ray fluorescence unit, which separates 20Cr from a plain 20 steel by the chromium reading and from 40Cr by the chromium and carbon trend.

Additional tests are ordered rather than assumed: ultrasonic testing to GB/T 5777 or ASTM E213 for internal soundness where the part is highly stressed; decarburisation depth check on the outside surface, because a decarburised layer will not respond to carburising as intended; and a hardenability test when the drawing calls for a declared band. Non-metallic inclusion rating to GB/T 10561 is a reasonable request for bearing and gear work.

Common Selection Errors

Three errors recur in enquiries for this grade. Treating 20Cr tube as equivalent to a 20 steel pipe for fluid service, which confuses an alloy structural grade with a pressure application. Assuming the mill certificate proves case hardness, when case hardness is created only by the buyer's heat treatment. And comparing 20Cr with 20CrMnTi on price alone, when the manganese-chromium grade carries better hardenability and may allow a smaller, lighter component that costs less overall.

A practical rule for the purchase order: state the grade with the standard number, the delivery condition and hardness, the dimensional standard and tolerance class, the test schedule and the documentation level. Add the end use, because a mill that knows the tube is going into a carburising furnace will control decarburisation and surface defects differently from one supplying general machining stock.

FAQ

Q: Is 20Cr seamless steel pipe a line pipe grade?
No. 20Cr is an alloy structural steel to GB/T 3077 for carburised mechanical parts. Piping for oil, gas or water is specified to API SPEC 5L, GB/T 9711, GB/T 8163 or ASME SA106, and 20Cr is not listed in those specifications.

Q: What tensile and yield strength does 20Cr deliver?
GB/T 3077 requires 835 MPa minimum tensile strength, 540 MPa minimum yield strength, 10 % minimum elongation, 40 % minimum reduction of area and 47 J minimum impact energy in the quenched and tempered condition, with hardness not above 179 HBW when annealed.

Q: Why is the elongation of 20Cr only 10 %?
Because the grade is designed for a hard carburised case over a low-carbon core, not for bending or welding as a pressure boundary. The low elongation figure is acceptable for a machined, hardened component and unacceptable as a substitute for a pipe grade that requires 20 % to 30 %.

Q: Can 20Cr tube be welded before carburising?
Yes, with a qualified procedure using preheat around 150 C to 250 C for thicker sections, low-hydrogen consumables and a post-weld temper. The weld must be completed and stress relieved before carburising, never after hardening.

Q: What is the difference between 20Cr and 20 steel?
20 steel to GB/T 699 has a carbon range of 0.17 % to 0.23 % and no deliberate chromium addition, giving 410 MPa tensile and 245 MPa yield. 20Cr adds 0.70 % to 1.00 % chromium, which raises hardenability so the grade can be carburised and hardened for wear resistance.

Q: Which standard covers the dimensions of 20Cr seamless tube?
Outside diameter and wall thickness tolerances are taken from GB/T 17395, with tighter classes by agreement, while the chemistry and mechanical properties come from GB/T 3077 and the product analysis tolerances from GB/T 222.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry