Why Weld Type Must Be Identified Before Any Inspection Plan Is Written
A welded steel pipe carries the same pressure and safety duty as a seamless pipe, but its integrity depends on one continuous seam that was created in the mill. The seam is also the region where almost every serious service failure starts. Because the three commercial welding routes - electric resistance welding, longitudinal submerged arc welding and spiral submerged arc welding - generate completely different defect populations, the inspection plan has to be selected from the weld type before a single test is scheduled.
Resistance welded pipe fails in a narrow, straight line and is dominated by cold welds, penetrators, hook cracks and seam annealing errors. Longitudinal submerged arc welded pipe fails in a wide, multi-pass weld where lack of fusion, slag entrapment and weld offset govern. Spiral welded pipe adds a helical geometry, a skelp end weld that intersects the spiral seam, and a much longer weld length per tonne of steel. Receiving a shipment described only as "welded pipe" is therefore not a documentation gap; it is a technical risk, because the wrong non-destructive method applied to the wrong seam geometry gives false confidence.
The practical sequence is: identify the weld type from the geometry and the marking, confirm the dimensional and chemical evidence, then apply the non-destructive and destructive tests that the governing standard requires for that specific product. API 5L and ISO 3183 define what must be demonstrated; the purchaser's technical annex defines what is additionally required for the project.
Visual Signatures of the Three Weld Families
An experienced inspector separates the three families in seconds using the seam geometry alone, then verifies with measurement.
Electric resistance and high-frequency welded pipe: a straight longitudinal seam that may be almost invisible after the external flash has been trimmed and the seam normalised. The weld line usually appears as a faint, narrow stripe with a shallow heat-affected band on either side and no filler metal bead.
Longitudinal submerged arc welded pipe: one straight seam with a distinct raised weld bead on both the inside and the outside surfaces, because the weld is made with filler wire under a granular flux in at least one pass per side. The seam is typically 12 to 25 mm wide depending on wall thickness and bevel preparation.
Spiral submerged arc welded pipe: a continuous helical seam crossing the full length of the pipe at an angle to the axis, with visible beads inside and outside, and usually a short transverse skelp end weld that meets the helix.
Two ambiguities are common. A longitudinal seam that has been fully normalised and then dressed can be mistaken for a seamless pipe, and a spiral pipe viewed from one end can look as though the seam runs straight. Checking both ends, following the seam for at least two metres, and reading the stencil will resolve both cases. Seamless pipe also shows faint helical tool marks from the piercing mill, but these are shallow surface marks without a heat-affected zone, without a weld bead and without a seam annealing colour band.
Dimensional and Wall Thickness Checks That Reveal Process Quality
Geometry is the cheapest quality signal available at goods-in. A pipe that has been formed and welded under control has a circular body, a straight axis, square-cut ends and a wall that stays inside the tolerance band around the full circumference and along the whole length.
API 5L sets wall thickness tolerances in Table 10 by pipe type and diameter class. For submerged arc welded pipe the minus tolerance is generally 12.5 % of nominal wall, with the plus side and the tighter resistance welded band tabulated separately for each diameter range. Diameter and out-of-roundness tolerances are also graded by size, with tighter limits at the pipe ends so that girth welding in the field remains feasible. Purchasers should quote the table values rather than an assumed percentage, because a 12.5 % wall loss on a 20 mm wall is 2.5 mm of load-bearing section that the design calculation did not account for.
Measurement practice matters as much as the limit. Ultrasonic thickness readings should be taken at four quadrants at both ends, at mid-length and at any position where the surface shows a step or a lap. A single reading at the twelve o'clock position of one end proves nothing. A wall map that shows a systematic thin zone adjacent to the seam points to forming or edge preparation problems; a random scatter points to plate or coil variability.
Chemistry, Certificate and Marking Cross-Checks
Grade cannot be identified visually. Grade B and X52 look identical, and the difference is a yield strength range of more than 100 MPa. Identification therefore depends on three linked pieces of evidence: the stencilled marking, the mill test certificate and, where doubt exists, independent chemical and mechanical testing.
The certificate review should confirm that the heat number on the certificate matches the stencil, that the product specification level is stated, that the delivery condition is stated, and that the mechanical results fall inside the grade table of the standard. Sulphur and phosphorus are worth specific attention because they control inclusion content, centreline segregation and weld toughness; a high carbon equivalent degrades field weldability regardless of how good the mill's welding was. For PSL2 pipe the certificate must also carry the non-destructive testing results and the impact test results at the specified temperature, because those are mandatory PSL2 requirements rather than optional extras.
Weld Zone Surface Condition and the Defects It Reveals
The seam is the most corrosion-prone and defect-prone region of any welded pipe, and most of its problems are visible before any instrument is used.
Undercutting: a groove melted along the weld toe that acts as a stress raiser and as a corrosion initiation site. It is measured against the limit in the applicable standard, not judged by eye alone.
Porosity and pinholes: gas trapped in the weld metal, often caused by damp flux, dirty edges or wrong polarity. Surface pinholes are an indicator that internal porosity may be present.
Incomplete fusion and lack of penetration: unfused interfaces inside the seam that reduce the effective load-bearing section and act as crack starters under cyclic pressure.
Weld offset: misalignment of the two plate or coil edges that concentrates strain at the seam and complicates ultrasonic interpretation.
Rust bleeding or scale at the seam: a sign of poor seam heat treatment, inadequate cooling control or wet storage, all of which shorten life in a corrosive environment.
For resistance welded pipe there is one additional defect that deserves its own place in the inspection plan: the cold weld, produced when the edges are brought together without sufficient heat input. The joint looks continuous from outside, carries almost no bond strength and can split along the seam under pressure without warning. It is detected by ultrasonic or eddy current testing of the full seam, not by visual inspection, which is why PSL2 pipe is supplied with full-length seam testing as a matter of course.
Matching Non-Destructive Methods to Weld Type
| Method | What it finds | Where it is most effective | Reference standard |
|---|---|---|---|
| Visual and dimensional | Surface defects, geometry, seam type, markings | Every pipe at receipt | API 5L, ISO 3183 |
| Full-body ultrasonic | Laminations, wall loss, transverse and longitudinal defects in the body | All welded pipe, especially heavy wall | ISO 10893-10, ASTM E213 |
| Seam ultrasonic | Lack of fusion, cold weld, penetrators, hook cracks | Resistance welded and submerged arc seams | ISO 10893-11, API 5L annexes |
| Eddy current | Short surface and near-surface seam discontinuities | Resistance welded seam at mill speed | ISO 10893-1, ISO 10893-2 |
| Radiography | Porosity, slag, lack of fusion in the weld volume | Longitudinal and spiral submerged arc seams, girth welds | ISO 10893-6, ASTM E94 |
| Magnetic particle | Surface and near-surface cracks | End bevels, weld toes, repair areas | ASTM E709, ISO 10893-5 |
| Hydrostatic test | Through-wall leaks and gross defects | Every finished pipe | API 5L, ISO 3183 |
Coverage is as important as method. A radiographic examination of a 20 % sample of a spiral seam examines 20 % of a weld that is several times longer per tonne than a straight seam. For critical lines the specification should state full-length testing by automatic ultrasonic equipment with a defined reference reflector and a defined acceptance level, and should require that the equipment calibration be recorded for each shift.
Destructive and Supplementary Checks
Non-destructive testing finds discontinuities; destructive testing proves the material. For PSL2 pipe the standard already requires tensile testing of the pipe body, Charpy impact testing of the body, seam and heat-affected zone at a specified temperature, and for larger diameters and higher grades a drop-weight tear test to demonstrate resistance to running fracture. On sour service orders, hardness surveys and hydrogen-induced cracking tests on the plate or pipe wall are added because hardness and inclusion shape, not tensile strength, control cracking resistance.
Supplementary checks that purchasers often add are: a flattening or bend test on a ring cut from the pipe end to expose seam ductility, a metallographic section across the seam to confirm fusion and heat treatment, and a seam tensile test that pulls the weld transverse to the axis. Each of these answers a question that the routine certificate does not answer. A bend test, for example, will open an incomplete fusion defect that a radiograph may have interpreted as acceptable.
Receiving Inspection Sequence for a Mixed Shipment
When a shipment contains more than one weld type, or when the documentation is incomplete, a fixed sequence keeps the inspection defensible. First, sort by seam geometry and marking, and record counts per type. Second, verify the stencil against the certificate for each bundle, and quarantine any bundle without a matching certificate. Third, run dimensional and wall thickness checks on a sample from each bundle. Fourth, confirm which non-destructive tests were performed at the mill and at what coverage level, then select the supplementary tests needed to close the gaps. Fifth, document every deviation with the pipe number, the position and the measured value, so that a claim can be raised against a specific unit rather than against the shipment as a whole.
That last point is where most receiving inspections lose value. A note that says some pipes had thin walls cannot support a commercial claim; a record that says pipe 41 at the twelve o'clock position of the delivery end measured 17.4 mm against a 20 mm nominal wall with a 17.5 mm minimum can.
FAQ
Q: How can electric resistance welded pipe be distinguished from seamless pipe on site?
Follow the surface for two metres and look for a straight weld line with a narrow heat-affected band and no filler bead. Seamless pipe has no seam, but it usually shows faint helical tool marks from piercing, and it never shows a seam annealing colour band.
Q: What is a cold weld in electric resistance welded pipe and why is it dangerous?
A cold weld forms when the edges are forged together without enough heat, so the bond is incomplete but the outside surface looks sound. It can open suddenly under pressure, and because there is almost no geometric signal it is found by full-seam ultrasonic or eddy current testing.
Q: Does a straight longitudinal seam indicate better quality than a spiral seam?
No. A straight seam gives a simpler weld geometry and is preferred for heavy wall and high pressure, while a spiral seam allows very large diameters from narrow coil. Quality depends on the welding procedure, the testing coverage and the dimensional control, not on the seam orientation.
Q: Why does the heat-affected zone need separate attention?
The heat-affected zone has a microstructure altered by welding heat and can become hard and brittle or, in some grades, soft and weak if the seam is not properly normalised or tempered. Impact testing and hardness checks of that zone are the only reliable evidence of its condition.
Q: Can the steel grade be confirmed from the pipe appearance alone?
No. Grade is confirmed by chemical analysis and mechanical testing, supported by the stencil and the mill test certificate. Visual appearance only reveals the manufacturing route and gross surface condition.
Q: Which test is compulsory on every welded pipe before dispatch?
The hydrostatic test is applied to every finished pipe to prove leak tightness at the specified test pressure. Non-destructive testing of the seam is required by the product specification level and by the purchaser's technical annex, and for PSL2 pipe full-length seam testing is standard practice.
Q: What wall thickness tolerance applies to a large submerged arc welded pipe?
The tolerance is taken from the wall thickness table of API 5L for the specific pipe type and diameter class, where the minus tolerance is generally 12.5 % of nominal wall for submerged arc welded pipe. The exact plus tolerance and the resistance welded band should be read from the standard rather than assumed.





