Aug 08, 2025 Leave a message

Angle Globe Valve: Working Principle, Types and Applications

Definition and Working Principle

An angle globe valve is a linear motion valve whose closing member is a plug shaped disc with a flat or conical sealing face. The disc travels along the centreline of the fluid path, and rotating the stem drives the disc up or down. This changes the gap between the disc and the seat and therefore controls the flow rate and the pressure drop across the valve. When the disc is fully seated the gap is zero and the valve is closed. The body of an angle globe valve turns the flow through 90 degrees between the inlet and the outlet, which is where the name comes from.

Structural Features

Right angle body, with the outlet at 90 degrees to the inlet, which replaces an elbow in the line and saves space.

Main components are the body, bonnet, stem, seat and sealing elements; the bonnet may be bolted, welded or of pressure seal design.

Sealing is achieved between disc and seat and between body and bonnet, and the joint is normally provided with a gasket or ring.

The stem is often surface hardened or nitrided to resist wear and galling, and may include an anti rotation feature to keep the disc aligned.

Stem sealing uses packing, and bellows seals are available for applications where zero stem leakage is required.

The trim can be supplied with a hardfaced cobalt chromium alloy facing for erosive or high temperature duty.

Specifications

Parameter Typical range or reference
Nominal size DN 15 to DN 400
Pressure class Class 150 to Class 2500
Body material ASTM A216 WCB, ASTM A217 WC6 and WC9, ASTM A351 CF8 and CF8M, ASTM A105
Design reference API 623 and API 602 for steel globe valves, BS 1873, ASME B16.34
Face to face ASME B16.10
End connections ASME B16.5 and ASME B16.47 flanges, ASME B16.25 butt weld, threaded on small sizes
Testing Shell and seat tests to API 598
Flow direction Normally inlet below the seat, so pressure assists closing

Classification

Angle globe valves can be grouped in several ways. By stem thread position they are divided into externally threaded and internally threaded types. By trim and body arrangement they appear as straight through, angle and oblique patterns. By sealing arrangement they are supplied as packing sealed or bellows sealed valves. Bonnet construction separates bolted bonnet, welded bonnet and pressure seal designs, and the choice follows the pressure class and the medium.

Applications

Angle globe valves are used in petrochemical, metallurgical, coal and power plant piping to regulate liquids, gases and steam, and in building water supply and drainage systems to adjust pressure and flow. They also serve urban water networks, irrigation and sewage treatment, oil and gas transfer systems, and chemical production lines where a compact throttling valve with a 90 degree turn is valuable. The angle pattern is particularly useful where the valve must also act as the elbow at the base of a vertical run.

Selection and Installation Guidance

Size the valve on the required flow coefficient rather than on the line size alone, because a globe valve that is too large will operate close to the seat and suffer vibration and erosion. Confirm the flow direction arrow before installation, keep the stem within the permitted orientation so that the packing is not starved of lubricant, and allow access for packing renewal. For high temperature steam service, choose a material class consistent with the pressure and temperature rating and provide a bonnet extension where the insulation would otherwise overheat the packing.

FAQ

Q: What is the main difference between an angle globe valve and a straight globe valve?
The internal working parts are the same; the difference is the body, which turns the flow through 90 degrees and therefore can replace an elbow at the point of installation.

Q: Can an angle globe valve be used for throttling?
Yes. The plug shaped disc and long stem travel allow progressive flow control, which is why globe valves are used where regulation rather than simple isolation is needed.

Q: Which standards apply?
API 623 and API 602 cover steel globe valves, BS 1873 covers flanged and butt welded steel globe valves, ASME B16.34 provides pressure and temperature ratings, and API 598 covers pressure testing.

Q: What is a bellows sealed angle globe valve used for?
The bellows forms a metallic barrier around the stem so that the medium cannot escape along the stem, which suits toxic, flammable or expensive fluids.

Q: Which way should the medium flow?
In most designs the medium enters below the disc so that line pressure helps to keep the valve closed and the packing is not exposed to full pressure when the valve is open.

Q: How often should the packing be renewed?
Packing life depends on the medium, temperature and the number of operating cycles. Renew it when leakage appears at the stem or when the gland has been tightened to its limit.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry