ERW and SAW Defined in Standard Terms
Every welded line pipe sold into a transmission or distribution project is classified first by its welding route, because that route decides which clauses of the purchase specification apply, which defects are physically possible, and which non-destructive inspection method can actually find them. API SPEC 5L uses explicit pipe type designations for this purpose: EW for electric welded pipe, SAWL for submerged arc welded pipe with a longitudinal seam, and SAWH for submerged arc welded pipe with a helical seam. Buyers who write "ERW or SAW acceptable" on a requisition without further qualification often receive two technically non-equivalent products at similar prices.
ERW in commercial usage covers high-frequency electric resistance welding (contact or induction), frequently shortened to HFW when induction coils are used. The strip or skelp is formed through a series of rolls, the two edges are heated to a forging temperature by high-frequency current concentrated at the edges, and the edges are squeezed together by pressure rolls without any filler metal. The weld is therefore a solid-state forged joint derived from the parent strip itself. SAW uses an arc struck under a blanket of granular flux between the work piece and one or more consumable wire electrodes; the arc, the molten weld pool and the solidifying metal are shielded from the atmosphere by the flux, and the weld metal is a distinct cast structure with its own chemistry.
The practical consequence is simple: an ERW seam has a very narrow heat-affected zone and no deposited weld metal, while a SAW seam has a wide, high-heat-input fusion zone with deposited metal whose toughness and hardness must be qualified separately from the pipe body.
How ERW Pipe Is Produced
Production starts from hot-rolled wide strip in coil. The coil is uncoiled, levelled and edge-trimmed, then accumulated in a loop so that the forming mill can run continuously. Forming is normally done in a cage-forming or series-of-rolls arrangement that progressively turns the flat strip into a cylinder with an open gap at the top. An impeder is positioned inside the tube immediately upstream of the weld rolls; its function is to concentrate the induced current in the strip edges rather than letting it circulate around the whole circumference.
Welding frequency for HFW is typically in the range of a few hundred kilohertz, and the power input, the Vee angle of the open edges and the squeeze force are the three variables that determine weld quality. After welding, the external and internal flash is removed by scarfing tools. Most line pipe specifications then require a seam heat treatment: the weld zone is normalised or induction-annealed so that the acicular, hard as-welded structure is softened and the hardness across the seam approaches that of the pipe body. This step matters for sour service, where ISO 15156 / NACE MR0175 imposes a maximum hardness of 250 HV10 in the weld and heat-affected zone, and for bending or field welding, where a hard seam can initiate cracking.
Sizing, straightening and hydrostatic testing follow. Because the process is continuous and coil-fed, ERW achieves good dimensional consistency, uniform wall thickness and a smooth surface, and it is the lowest-cost route for small and medium diameter thin-wall pipe.
How SAW Pipe Is Produced
Longitudinal SAW (LSAW) begins with discrete plates rather than coil. Plate edges are milled or planed to a controlled bevel, then formed into a tube by one of three forming routes: UOE (U-press, O-press, then mechanical or hydraulic expansion), JCOE (incremental J-ing and C-ing then O-ing, followed by expansion), or three-roll bending. The formed shell is tack welded, and the longitudinal seam is then welded from the inside and from the outside in separate passes, each covered by flux that is recovered, screened and reused.
Helical SAW (SSAW) begins with coil or plate that is fed into a spiral forming unit at a controlled helix angle. The strip edges meet along a helix, and the seam is welded simultaneously on the inside and the outside by two or three wire tandem heads. Because the helix angle and the strip width jointly set the finished diameter, SSAW can produce very large diameters from a modest strip width, and the same coil can be turned into several pipe sizes. The trade-off is a longer seam length per metre of pipe, a weld that crosses the plate rolling direction, and a residual stress pattern that needs attention during end preparation.
Both SAW variants are followed by mechanical expansion or sizing, hydrostatic testing, and where specified, ultrasonic or radiographic inspection of the full seam length. Weld toughness, hardness and shear-area requirements in the weld metal and heat-affected zone are qualified through welding procedure tests that must be repeated when consumables, flux, heat input or plate source change.
Side-by-Side Comparison of ERW, LSAW and SSAW
| Characteristic | ERW / HFW | LSAW | SSAW |
|---|---|---|---|
| Weld type | Solid-state forged seam, no filler metal | Fusion weld, one straight longitudinal seam | Fusion weld, helical seam, welded inside and outside |
| Typical outside diameter | 21.3 mm to 610 mm | 406 mm to 1626 mm | 219 mm to over 2500 mm |
| Typical wall thickness | 2 mm to 16 mm, limited by wall-to-diameter ratio | 6 mm to 40 mm and heavier | 5 mm to 25 mm |
| Seam length per metre | 1 m | 1 m | 1.1 m to 3 m depending on helix angle |
| Heat input | Very low, narrow heat-affected zone | High, multi-wire tandem possible | High, two-sided simultaneous |
| Dimensional accuracy | Best wall uniformity and ovality control | Good, improved by expansion | Moderate, diameter set by strip width and angle |
| Typical defect risk | Cold weld, lack of fusion, hook crack, penetrator | Weld metal porosity, slag, HAZ hardness, seam misalignment | Seam misalignment, slag lines, helix-related ovality |
| Best inspection route | Ultrasonic or electromagnetic seam tracking, hydrostatic test | Automatic ultrasonic plus radiographic sampling | Automatic ultrasonic of both seam sides plus radiographic sampling |
| Main applications | Distribution mains, water, low and medium pressure service | High-pressure transmission, station piping, offshore structures | Large-diameter transmission, piling, water transmission |
Weld Imperfections and How They Are Found
The defect families differ because the physics differ. In ERW, the classic failure modes are cold weld (insufficient heat or squeeze, so the joint is forged but not bonded), stitch or lack of fusion along the seam, hook cracks that run into the wall from the weld interface, and penetrators, which are oxide or non-metallic inclusions trapped in the seam. These are planar and metallurgical, and they are best found by ultrasonic testing of the weld seam as described in ISO 10893-11, by electromagnetic methods such as flux leakage, or by the ultrasonic weld tracker systems used in continuous production. Radiography is comparatively weak against tight lack-of-fusion in ERW, which is why an ERW supplier offering only radiographic seam inspection is a warning sign for high-pressure duty.
In SAW, the common imperfections are slag inclusions, porosity from damp flux or dirty plate edges, incomplete fusion between weld passes, undercut, and hydrogen-assisted cracking when the flux has not been properly baked. Weld metal chemistry, oxygen content and flux basicity govern toughness, and this is why the flux batch and the wire heat number must be recorded. Radiography per ISO 10893-6 or ASTM E94 is effective against slag and porosity; automated ultrasonic testing per ISO 10893-11 and ASTM E213 covers planar lack of fusion; magnetic particle testing per ASTM E709 is used on seam ends and on repair areas; penetrant testing per ASTM E165 is used mainly on stainless and on weld preparations.
Regardless of route, API SPEC 5L requires a hydrostatic test, held at a pressure derived from the specified hoop stress, and PSL2 pipe requires Charpy V-notch impact testing of the pipe body, the weld and the heat-affected zone at the specified test temperature. For low-temperature service the test temperature is what separates an acceptable offer from a cheap one: the same pipe grade can be quoted for a -5 degree Celsius test or a -45 degree Celsius test, and the second requires a different steelmaking practice, calcium treatment for inclusion shape control and tighter process windows.
Sizes, Tolerances and Standard Clauses That Decide Acceptance
Diameter and out-of-roundness tolerances in API SPEC 5L are defined by pipe type and size range, and welded pipe carries separate limits for the pipe body and for the seam. Wall thickness tolerance is likewise split: the weld seam area and the pipe body are treated differently, and the permissible minus tolerance is what a designer must deduct when calculating the pressure containment. A purchaser comparing two offers at the same nominal wall must therefore compare the guaranteed minimum wall, not the nominal figure.
End preparation is another frequent source of rejection. Pipe is normally supplied with bevelled ends at 30 degrees with a tolerance in the plus direction, a root face of roughly 1.6 mm, and a specified end squareness; if the pipe is to be girth welded in the field with an automatic system, the internal diameter and ovality at the ends become critical and are often tightened by project specification beyond the base standard. Length tolerances, straightness and the position of the seam relative to the top of the pipe during installation are all contractual clauses worth writing down before the order is placed.
Documentation is part of acceptance. An inspection certificate to EN 10204 type 3.1 must link the delivered pipe to the specific heat and to the specific test results, and for pipeline projects the additional requirements of ISO 3183 or GB/T 9711 are often invoked alongside API SPEC 5L, with project-specific supplements for fracture control, sour service per ISO 15156 and offshore use per DNV-ST-F101.
Choosing the Right Welding Route
Choose ERW when the diameter is below roughly 24 inches, the wall is thin relative to the diameter, the service is distribution gas, water, slurry or low-pressure process piping, and dimensional accuracy and cost per metre dominate. Choose LSAW when the diameter is large, the wall is heavy, the design factor is high, and the seam must deliver guaranteed toughness at low temperature; large-diameter high-pressure gas transmission and offshore structural pipe normally fall here. Choose SSAW when very large diameters are needed for water transmission, outfall lines, piling or lower-pressure gas service, and when the commercial advantage of making a large diameter from a narrow strip outweighs the longer seam.
Three selection rules save rework. First, match the pipe type to the inspection method available at the mill, not only to the price list. Second, state the impact test temperature, the shear area requirement and the hardness limit explicitly, because these are the properties that separate a compliant PSL2 pipe from a PSL1 pipe in disguise. Third, require the weld seam hardness survey and the seam annealing record for ERW pipe intended for sour or wet service, since an un-annealed seam will fail an ISO 15156 hardness check no matter how good the tensile results look.
Frequently Misunderstood Points
A common claim is that ERW is stronger than SAW. Neither route determines strength; the grade, the chemistry and the heat treatment determine strength, and the weld is required to reach the specified minimum tensile strength in either case. Another claim is that a double-sided SAW seam is defect-free by definition. Full penetration improves the joint, but slag, porosity and lack of fusion between passes remain possible and are only excluded by qualified procedures plus inspection.
A third misunderstanding concerns the word seamless. ERW pipe is often marketed as an alternative to seamless pipe, which is true on cost and dimension but not on pressure rating: a seamless pipe has no seam and therefore no seam-related inspection burden, and for critical small-diameter high-pressure service the correct comparison is between seamless and cold-drawn or hot-finished seamless, not between ERW and SAW. Finally, the presence of a hydrostatic test does not prove seam integrity under service loads; the hydrostatic test screens gross leaks, while the ultrasonic seam inspection is what screens planar lack of fusion.
FAQ
Q: Can ERW pipe be used for high-pressure natural gas transmission?
Yes, within its size and wall range and when the purchase order invokes the PSL2 requirements of API SPEC 5L including Charpy testing of the weld and heat-affected zone, seam annealing and full-length ultrasonic seam inspection to ISO 10893-11. Above roughly 24 inches in diameter, or where heavy wall and low-temperature toughness are required, LSAW is normally the specified route because heavy-wall ERW is limited by the wall-to-diameter ratio that the forming and welding rolls can handle.
Q: What is the difference between LSAW and SSAW in terms of performance?
Both are submerged arc welded and both are covered by API SPEC 5L as SAWL and SAWH respectively. LSAW has a single straight seam of one metre per metre of pipe, better roundness after expansion and a weld whose direction is parallel to the pipe axis, which suits high-pressure gas transmission. SSAW has a helical seam, so seam length per metre is longer and the weld crosses the rolling direction of the plate, which is why SSAW is preferred for very large diameters and for water and piling service rather than for the most demanding gas lines.
Q: Why does ERW pipe need seam heat treatment?
The high-frequency welding cycle produces a narrow, hard, acicular structure at the seam and in the adjacent heat-affected zone. Normalising or induction annealing of the seam restores ductility, reduces hardness to a level compatible with the pipe body, and allows the pipe to satisfy the 250 HV10 maximum hardness commonly imposed for sour service under ISO 15156 / NACE MR0175. It also improves the behaviour of the seam during field girth welding and cold field bending.
Q: Which non-destructive test finds lack of fusion in an ERW seam?
Ultrasonic testing of the weld seam, normally automated and performed in line, is the effective method for planar lack-of-fusion and cold weld, and it is standardised in ISO 10893-11 with reference to ASTM E213 practice. Radiography is comparatively insensitive to tight, planar, oxide-free lack of fusion in a forged seam, so a radiographic-only inspection programme does not give equivalent assurance for ERW line pipe.
Q: Does the welding route affect the price more than the steel grade?
Both matter, but in different ways. The welding route changes the capital and conversion cost, the achievable size range and the inspection cost, and it therefore sets the base price per tonne for a given diameter and wall. The steel grade changes the alloy addition, the steelmaking route, the rolling practice and the testing burden, which is why the step from a PSL1 grade to a PSL2 grade with low-temperature Charpy testing often costs more than a small change of diameter. A like-for-like comparison must fix diameter, wall, length, grade, PSL, test temperature, end finish and coating before prices are compared.
Q: What documents should accompany a welded pipe shipment?
At minimum, an inspection certificate to EN 10204 type 3.1 giving heat number, chemical composition, tensile results, impact results and hydrostatic test pressure, plus the dimensional inspection record and the non-destructive testing reports with the operator and procedure identification. Pipeline projects normally add coating certificates, third-party inspection release notes and, for sour service, a hardness survey of the weld and heat-affected zone. Records must be traceable to the individual pipe or bundle markings, otherwise the certificate is of little value at the receiving inspection.





