Hot Rolled Tube and Cold Rolled Tube: Two Different Manufacturing Routes
The terms hot rolled and cold rolled describe the temperature at which the tube is formed, and that single difference controls almost everything a buyer cares about: dimensional accuracy, surface condition, mechanical properties, residual stress, available length, minimum order quantity and price. A hot rolled tube is formed from a billet at a temperature around 1150 to 1250 degrees C, where the steel is soft enough to be pierced and elongated by rolls. A cold rolled tube starts from a hot rolled hollow that is then reduced at room temperature, either by cold pilger rolling or by cold drawing, with an annealing step between passes to restore ductility.
The distinction is often confused with the difference between seamless and welded, which is a separate question about whether a seam exists. Both hot rolled and cold rolled tube can be seamless; both can also be produced from welded hollows that are subsequently cold reduced. For purchasing purposes the two questions must be answered independently: first whether a seam is permitted, then which finishing route is required by the drawing, the tolerance, the surface and the mechanical property specification.
How the Hot Rolled Route Works
In the seamless hot route a round billet is heated to a uniform rolling temperature and pierced to form a thick-walled hollow, which is then elongated on a mandrel mill, a plug mill, an Assel mill or a push bench to reduce the wall and extend the length. The tube is then reworked in a sizing mill to bring the outside diameter within tolerance, straightened while still warm, and cooled on a cooling bed. If a heat treatment is required by the product standard, it follows after cooling, usually normalizing at roughly 900 to 950 degrees C for carbon and low-alloy grades.
Because every deformation step happens above the recrystallization temperature, the steel continuously recovers from the deformation. The resulting structure is equiaxed and reasonably uniform, the residual stress level is low, and the tube can be supplied in long random lengths. The limitation is dimensional: at high temperature the rolls wear, the tube ovalizes as it leaves the stand, the wall drifts eccentrically around the bore, and the surface carries oxide scale that must be removed by descaling or by a subsequent conditioning operation.
Hot rolled tube therefore dominates where the wall is thick, the length is long, the quantity is large and the tolerance requirement is moderate. Boiler and superheater tube in ASTM A106, ASTM A335 and EN 10216-2, large-diameter line pipe and structural hollow sections are typically hot finished, because the rolling route can deliver the wall thickness and the tonnage economically and the standards allow a tolerance band consistent with hot working.
How the Cold Rolled and Cold Drawn Route Works
The cold route begins with a hot rolled hollow, called the mother tube, which is conditioned to remove scale and surface defects, then coated with a lubricant carrier before being reduced at room temperature. Two processes dominate. Cold pilger rolling passes the tube over a stationary mandrel between reciprocating dies, reducing wall and diameter in a series of small steps and producing a characteristic uniform wall with a bright surface. Cold drawing pulls the tube through a die over a plug or without a plug, reducing diameter and wall in one pass and producing very tight diameter control.
Cold deformation raises the yield and tensile strength by work hardening, so each pass is followed by an anneal, or a series of passes is followed by a final heat treatment, to restore the ductility needed for the next reduction or for the finished application. The final thermal step is the one that determines the delivery condition and therefore the properties the buyer receives. EN 10305-1 and DIN 2391 define the options explicitly: cold drawn hard with no final heat treatment, soft annealed for maximum formability, stress relieved to reduce residual stress while keeping some work hardening, annealed, and normalized.
The cold route buys accuracy at the cost of process time. A single cold drawing pass may reduce the section by ten to thirty percent, so a large reduction needs several passes, each with its own cleaning, lubrication, drawing and annealing cycle. That is why cold drawn tube costs a multiple of hot rolled tube of the same size, and why the price difference grows as the wall becomes heavier and the reduction ratio larger.
Table: Dimensional and Property Comparison
| Characteristic | Hot finished tube | Cold drawn or cold rolled tube |
|---|---|---|
| Outside diameter tolerance, small to medium size | About plus or minus 1 percent, with a minimum of 0.5 mm | Typically plus or minus 0.10 to 0.20 mm, tighter on special finishes |
| Wall thickness tolerance | Commonly minus 12.5 percent to plus 15 percent | Typically plus or minus 10 percent, or a minimum wall guarantee |
| Concentricity and eccentricity | Wall may vary noticeably around the circumference | Wall variation is small and repeatable |
| Surface | Oxide scale after cooling, removed by descaling when required | Bright, smooth, suitable for plating, honing and sealing |
| Yield and tensile strength | Set by the grade and the final heat treatment | Raised by work hardening unless a final anneal is applied |
| Elongation | Typically 20 percent and above | As low as 8 to 12 percent in the hard condition, restored by annealing |
| Residual stress | Low | Significant unless stress relieved |
| Straightness and length | Long random lengths, moderate straightness | Short fixed lengths, high straightness |
| Relative cost at equal size | Base | Higher, increasing with reduction ratio and annealing cycles |
Mechanical Properties and Delivery Condition
The single most important lesson for a purchaser is that the delivery condition, not the processing route, determines the properties that can be certified. A cold drawn tube in the hard condition can show a yield strength fifty percent above the same steel in the annealed condition, but with an elongation that may not satisfy a bending or flaring requirement. A cold drawn tube that has been stress relieved recovers much of its ductility while retaining part of the work hardening, and a fully annealed tube behaves like the hot finished product of the same grade.
The consequence is that the drawing or the specification must state the condition explicitly. A requirement written as cold drawn without a condition code gives the supplier freedom to deliver hard, stress relieved or annealed tube, all of which comply with the words and none of which are interchangeable in a machining, welding or pressure application. Where the tube is subsequently bent, swaged, flared or welded, the annealed or stress relieved condition is normally required; where it is machined into a bushing or a shaft, the hard condition may be preferred for strength and surface finish.
Work hardening also affects the shape of the stress-strain curve. Cold worked tube has a lower uniform elongation, which reduces the strain the material can absorb before necking, and it has no distinct yield plateau. In pressure design the allowable stress is taken from the specified minimum yield strength at temperature, so a work hardened tube is not automatically permitted at a higher design pressure unless the specification allows the higher value to be used.
Standards and What Each One Actually Controls
Hot finished tube is governed by standards that define the grade and the allowable property range but leave the tolerance band relatively wide. EN 10216-1 covers non-alloy seamless pressure tube with specified room temperature properties, EN 10216-2 covers elevated temperature grades such as P265GH, ASTM A106 covers carbon steel seamless pipe for high temperature service in grades A, B and C, and ASTM A335 covers ferritic alloy pipe for high temperature service. Each of these accepts a hot finished surface and a tolerance band appropriate to hot working, and each requires hydrostatic or non-destructive testing plus tensile and, where applicable, impact testing.
Cold finished tube is governed by standards that treat the cold reduction as part of the product definition. DIN 2391-1 and EN 10305-1 define seamless cold drawn precision tube in grades such as E235 and E355 with the condition codes for hard, soft annealed, stress relieved, annealed and normalized delivery. EN 10305-4 applies the same family to hydraulic and pneumatic power systems, where the bore cleanliness and the dimensional accuracy are part of the acceptance criteria. ASTM A519 covers seamless carbon and alloy mechanical tube in a wide range of grades and conditions, ASTM A213 covers cold finished austenitic and ferritic alloy boiler tube, and ASTM A269 covers cold finished austenitic tube for general service.
For each standard the buyer should confirm three things: which condition is being supplied, which test frequency applies, and which tolerance table governs the size ordered. A quotation that cites a standard without the condition and the tolerance class has not defined the product.
Where Cold Finishing Pays and Where It Does Not
Cold finishing is justified when the application cannot tolerate the tolerance band of a hot finished tube. Hydraulic cylinder barrels require a bore that can be honed to a sealing surface with a repeatable clearance, and the wall must be concentric enough that the honing allowance is uniform; a hot rolled tube with an eccentric wall forces a heavier starting wall and more machining. Precision mechanical tube for bearings, shafts, rollers and automotive components requires a diameter that can be machined or ground with a small allowance, and often a surface free of scale, which is exactly what cold drawing delivers.
Heat exchanger and condenser tube is a second large application. The tube must pass through tube sheets and baffles with a defined clearance, the wall must be thin but uniform for heat transfer, and the surface must be clean enough for the corrosion resistance of a stainless or alloy grade to be realised. Cold finished tube to ASTM A213 or ASTM A269 meets those requirements; a hot finished tube of the same analysis would need additional machining to reach them.
Cold finishing does not pay when the wall is heavy, the length is long, the quantity is large and the tolerance is not critical. Structural hollow sections, piling, large-diameter line pipe, and general low-pressure service pipe are almost always hot finished, because the cold route would multiply the cost without adding usable accuracy. The break-even sits roughly where the machining allowance saved by the tighter tolerance equals the price difference between the two routes.
Residual Stress, Straightness and Dimensional Behaviour After Fabrication
Cold deformation leaves a through-wall residual stress pattern that is beneficial in fatigue resistance under some loading but harmful in others. The compressive stress at the surface can improve fatigue life in a machined component, while the tensile stress in the bore accelerates stress corrosion cracking in a chloride environment and distorts the tube when one surface is machined away. Stress relieving after the final cold pass removes most of this risk, and for stainless grades the final solution anneal is required anyway to restore corrosion resistance after work hardening.
Residual stress also explains a common field complaint: a cold drawn tube that measures straight on the rack may bow after a longitudinal cut or after machining one side. The released stress redistributes and the tube bends. Operators who plan to machine a flat or a keyway on a cold drawn tube should specify the stress relieved condition, not the hard condition, and should expect that some straightening will still be necessary.
Ovality and wall eccentricity behave in the opposite way. Hot rolled tube can be oval within the tolerance band and can show a wall that drifts around the circumference, both of which become visible when the tube is machined or when it is rolled for a bend. Cold drawn and cold rolled tube holds concentricity closely because the final passes size both the outside diameter and the wall on a mandrel.
Inspection, Testing and Acceptance
Both routes end with the same obligation to prove the product. Hydrostatic testing at a pressure calculated from the wall and the allowable stress, or an approved non-destructive substitute, is standard for pressure tube. Ultrasonic testing detects longitudinal and transverse defects in the wall, eddy current testing is used for thin wall and for austenitic grades where ultrasound is difficult, and for cold finished tube the dimensional inspection includes diameter, wall, length, straightness and, where specified, bore cleanliness.
For cold finished tube the certificate should also state the delivery condition code and the final thermal treatment parameters. A certificate that reports tensile results consistent with the hard condition while the order called for stress relieved tube is a non-conformity even though the numbers pass the minimum. For heat exchanger tube the additional tests are usually a flaring or flattening test, a hardness survey, and for austenitic grades an intergranular corrosion test or a corrosion-resistant qualification.
Where the tube will be welded into a pressure part, the welding procedure must be qualified on the delivered condition. A hard cold drawn tube welds with a different heat-affected zone hardness and a different risk of cracking than an annealed tube of the same analysis, so the qualification should be performed on production material and not on a generic coupon.
Frequently Asked Questions
Q: Is cold rolled tube always stronger than hot rolled tube?
In the hard condition, yes, because work hardening raises the yield and tensile strength. Once a final anneal or normalize is applied the strength returns to the level of the grade, so cold drawn and hot finished tube of the same grade and condition have comparable strength. The delivery condition, not the route, sets the properties.
Q: Why is cold drawn tube more expensive?
Each cold pass reduces the section only by a limited amount, so several drawing passes with intermediate cleaning, lubrication and annealing are needed. The additional operations, the yield loss and the annealing energy explain the price difference, which grows with the reduction ratio and the wall thickness.
Q: Which route gives tighter wall thickness tolerance?
Cold drawing or cold pilger rolling on a mandrel gives the tighter and more repeatable wall. Hot finished tube typically allows a band of about minus 12.5 percent to plus 15 percent on wall, while cold finished precision tube commonly holds about plus or minus 10 percent or a guaranteed minimum wall.
Q: Can hot rolled tube be used for hydraulic cylinders?
Only with additional machining. A hydraulic cylinder barrel needs a concentric bore and a uniform honing allowance, which a hot finished tube with wall eccentricity does not guarantee. Cold drawn or honed tube to a precision standard is the normal choice for that duty.
Q: What does the delivery condition code on a cold drawn tube mean?
The code states the final thermal treatment. Hard means no final heat treatment after the last cold pass, soft annealed means fully softened for formability, stress relieved means residual stress is reduced while some work hardening is kept, and annealed or normalized means the properties are restored to the grade level.
Q: Does cold working affect corrosion resistance?
For carbon and low-alloy steel the effect is small. For austenitic stainless steel, cold work can reduce resistance to chloride stress corrosion cracking and, if the grade is sensitized, to intergranular attack, which is why a final solution anneal is required after cold reduction in the relevant product standards.





