Aug 15, 2024 Leave a message

309S vs 310S Stainless Steel: Temperature Limits and Selection

Two High-Chromium, High-Nickel Austenitic Grades in One Family

309S and 310S are both fully austenitic stainless steels built for elevated temperature service. They share the same carbon ceiling of 0.08 %, the same 2.00 % manganese maximum and the same absence of deliberate molybdenum or titanium additions, and they are both supplied under the same product standards. What separates them is the amount of chromium and nickel: 309S carries 22.0 % to 24.0 % chromium with 12.0 % to 15.0 % nickel, while 310S carries 24.0 % to 26.0 % chromium with 19.0 % to 22.0 % nickel. That gap of roughly 2 % chromium and 6 % nickel is the whole story of the application difference, the price difference and the welding difference.

Their UNS numbers are S30908 and S31008. The trailing S is meaningful: it marks the low-carbon variant of the original 309 and 310 compositions, which were capped at 0.20 % carbon. Lowering carbon to 0.08 % maximum reduces carbide precipitation in the 425 °C to 815 °C range and makes welded joints far less prone to intergranular attack, which is why the S variants are what the market actually buys for tube and plate.

Governing specifications include ASTM A312/A312M for seamless and welded austenitic pipe, ASTM A213/A213M for seamless heat exchanger and boiler tube, ASTM A249/A249M for welded heat exchanger tube, ASTM A240/A240M for plate, sheet and strip, ASTM A276/A276M and ASTM A479/A479M for bar, and ASTM A358/A358M for electric-fusion-welded pipe. The European designations are 1.4833 for 309S and 1.4845 for 310S under EN 10095 for heat-resisting steels, and the Japanese equivalents are SUS309S and SUS310S under JIS G3459 and JIS G3463.

Chemical Composition Compared

The chromium level sets the maximum temperature at which a coherent protective oxide can survive. The nickel level stabilises the austenite that the higher chromium would otherwise destabilise, and it also raises the creep strength and the resistance to carburisation and nitridation. In 310S the nickel is high enough at 19 % to 22 % that the alloy can hold 25 % chromium in a fully austenitic structure without delta ferrite, which is why 310S welds solidify as a single-phase austenite and behave differently from the more common 304 and 316 grades.

Silicon differs between the two grades in the standard tables: 309S is normally specified at 0.75 % maximum and 310S at 1.50 % maximum. Silicon improves oxidation resistance, so the higher allowance in 310S is consistent with its higher temperature capability. Both grades keep phosphorus at 0.045 % maximum and sulphur at 0.030 % maximum in the ASTM austenitic specifications, and both are non-magnetic in the annealed condition because the structure is austenitic at room temperature.

Property 309S (UNS S30908) 310S (UNS S31008)
Carbon, max 0.08 % 0.08 %
Chromium 22.0–24.0 % 24.0–26.0 %
Nickel 12.0–15.0 % 19.0–22.0 %
Silicon, max 0.75 % 1.50 %
Manganese, max 2.00 % 2.00 %
Tensile strength, min 515 MPa 515 MPa
Yield strength 0.2 %, min 205 MPa 205 MPa
Elongation in 50 mm, min 40 % 40 %
Solution annealing range 1035–1120 °C 1040–1150 °C
Practical continuous service ceiling about 1000 °C about 1100 °C
Intermittent service ceiling about 980 °C about 1035 °C

Maximum Service Temperature and the Oxide Film

The difference in published service ceilings is usually stated as about 1000 °C for 309S and about 1100 °C for 310S in continuous operation, with lower figures for cyclic service because thermal cycling spalls the oxide and each spall exposes fresh metal. These are not arbitrary marketing numbers; they follow from the chromium activity at the surface. With 22 % to 24 % chromium, 309S forms a chromium-rich oxide of the Cr₂O₃ type that grows slowly and stays adherent up to roughly 1000 °C. With 24 % to 26 % chromium and higher silicon, 310S maintains that film to a higher temperature before internal oxidation and nodular scaling begin.

The nickel contribution is often underestimated. Nickel does not form a protective oxide in the way chromium does, but it keeps the matrix austenitic so that the chromium can diffuse to the surface without being locked up in ferrite, and it reduces the solubility of carbon and nitrogen, which lowers the driving force for internal carburisation. This is why 310S holds up better than 309S not only in air but in carburising and nitriding atmospheres and in the presence of sulphur-free combustion products.

Both grades have a firm limit in sulphur-bearing atmospheres. Reducing gases containing hydrogen sulphide, or fuel-rich combustion gases with high sulphur, attack the chromium oxide and cause rapid sulphidation above roughly 600 °C to 700 °C. In those environments neither grade is the right answer, and higher-nickel or nickel-base alloys are required instead.

Mechanical Behaviour at Temperature

At room temperature the two grades are almost interchangeable: both meet 515 MPa tensile, 205 MPa yield and 40 % elongation as specified minimums for austenitic tube and pipe. The separation appears above about 600 °C. Higher nickel and chromium raise the creep rupture strength, so 310S carries a higher allowable stress in the ASME Boiler and Pressure Vessel Code tables than 309S at the same temperature, and the gap widens as temperature increases.

Thermal expansion is high for both, in the region of 14.5 to 16.0 × 10⁻⁶ per kelvin over 20 °C to 500 °C, which is about 40 % higher than carbon steel. A designer must therefore allow for expansion in any restrained run, and dissimilar joints to carbon steel or to lower-alloy stainless need expansion compensation rather than a rigid connection. Thermal conductivity is low, around 14 to 16 W/m·K at room temperature, so thermal gradients through the wall are steeper than in carbon steel and thermal fatigue at restraint points is a real design case.

Long-term exposure in the 600 °C to 900 °C band precipitates sigma phase in both grades, and more readily in 310S because of its higher chromium and nickel combination. Sigma is hard and brittle, it removes chromium and molybdenum from the matrix, and it degrades both toughness and corrosion resistance. The practical rule is that these grades are meant for service either above the sigma-forming range or below it, not for long holds inside it.

Corrosion Resistance Beyond Oxidation

309S is often selected for a mixed duty where high-temperature oxidation resistance is needed and a moderate aqueous corrosion resistance is a bonus. Its chromium and nickel levels give it better resistance than 304 in mildly acidic and oxidising aqueous media, and it withstands dilute sulphuric and nitric acid environments better than the 18-8 grades. It is not a substitute for 316L in chloride service: molybdenum is absent, so pitting resistance in chlorides is limited regardless of the chromium level.

310S performs better in oxidising, reducing and neutral high-temperature gases and resists many hot acid and alkaline conditions, but it also lacks molybdenum and should not be chosen for wet chloride pitting duty. In aqueous chloride environments both grades are inferior to 316L and far inferior to the duplex and super-austenitic grades. Where chlorides plus wetness plus stress coincide, stress corrosion cracking of austenitic grades is a design risk and the correct answer is a duplex or higher-alloy grade, not more nickel alone.

Fabrication, Welding and Heat Treatment

Both grades are readily cold formed and machined, with work hardening rates similar to 304 and somewhat higher than 316 because of the higher alloy content. They are supplied solution annealed and should not be stress relieved by slow cooling, which would precipitate carbides and sigma; any thermal treatment that is required must be a full solution anneal at 1035 °C to 1150 °C followed by rapid cooling.

Welding needs attention. Because 310S is fully austenitic with no delta ferrite to dissolve sulphur and phosphorus, it is more sensitive to solidification cracking than 304 or 316, and welds should be made with low heat input, a slight weave-free stringer technique, controlled interpass temperature and a filler chosen for the duty. Matching filler metals of the 309 and 310 type are available for both grades, and a nickel-base filler is commonly used on 310S where a crack-resistant, high-temperature joint is required. 309S has a small amount of ferrite in the weld metal when welded with matching filler, which makes it more forgiving.

Preheat is not used on either grade, since preheating an austenitic steel serves no purpose and only increases the risk of sensitisation and distortion. Post-weld heat treatment is also normally omitted; if it is needed for dimensional reasons, it must be a full solution anneal, because a low-temperature stress relief in the carbide range does more harm than good.

Pickling and passivation after welding apply to both, with the same caution: the pickling acid must be formulated for high-alloy austenitic steel, and residue must be fully rinsed to avoid later attack in service.

Applications and Selection Rules

309S is the workhorse of the mid-temperature range. It is used for furnace parts that see 900 °C to 1000 °C, radiant tube supports, annealing box and tray work, heat treatment fixtures, kiln internals, boiler baffles and supports, and transition pieces where a 304 component meets a higher-temperature section. It is also used for the weld overlay and the dissimilar joint between a low-alloy part and a higher-alloy part, because its intermediate composition reduces the dilution problem.

310S is chosen when the temperature is above about 1000 °C or when the atmosphere is carburising. Typical duties are furnace muffle and retort, radiant tubes, burner nozzles, incinerator internals, cement kiln and lime kiln components, glass industry parts, thermocouple protection tubes, and reformer and pyrolysis furnace tube where carburisation and creep both matter. In the power and process industries it is used in superheater supports and in high-temperature flue gas ducting where 309S would scale too quickly.

The selection rule that saves the most money is to match the grade to the hottest sustained metal temperature plus a margin, not to the average gas temperature. A furnace with a 1050 °C set point will have metal temperatures at the supports and in the flue path considerably above that, and 309S installed in such a position will scale and lose section within a few campaigns, whereas 310S will survive. Conversely, using 310S for a 900 °C duty buys nothing except a higher nickel bill.

Cost, Supply and Ordering Considerations

Nickel is the dominant cost driver in both grades, and the difference between 12 % to 15 % nickel and 19 % to 22 % nickel translates directly into price per tonne. That means the choice between the two should always be justified by service temperature and atmosphere, documented, and not left to habit. Mill lead times also differ, because 310S is a lower-volume product and not every tube mill keeps it in stock in every size.

An order for either grade should state the grade with its UNS number, the product standard with edition, the delivery condition as solution annealed and pickled or bright annealed, the outside diameter and wall with tolerances, the length type, and the test list. For high-temperature service, add the intergranular corrosion test to ASTM A262 Practice E for welded sections, the grain size requirement to ASTM E112 where creep life matters, and a requirement that the mill record the actual solution annealing temperature on the inspection certificate.

Buyers should also ask about the surface finish, because a residual heat tint or an incompletely removed weld oxide is the most common cause of a premature failure in these grades. The oxide layer is not only cosmetic, it consumes chromium from the underlying metal and leaves it unable to reform a protective film in service. A properly pickled and passivated surface, or a bright annealed surface with a controlled atmosphere, is worth more in service life than an extra millimetre of wall.

FAQ

Q: What is the main difference between 309S and 310S stainless steel?
The alloy content and therefore the temperature capability. 309S has 22.0–24.0 % chromium and 12.0–15.0 % nickel with a service ceiling near 1000 °C, while 310S has 24.0–26.0 % chromium and 19.0–22.0 % nickel with a ceiling near 1100 °C. Both are low-carbon austenitic grades with a 0.08 % carbon maximum and identical room-temperature minimum strength.

Q: Can 309S be used at 1100 °C?
Not for sustained service. At 1100 °C the chromium-rich oxide on 309S breaks down and rapid scaling begins, with loss of section and eventual perforation. Short excursions may be tolerable in a non-cyclic, low-stress application, but a sustained 1100 °C duty requires 310S or a higher-alloy heat-resisting grade.

Q: Is 310S more corrosion resistant than 309S in seawater?
No. Neither grade contains molybdenum and both are vulnerable to chloride pitting and crevice attack in seawater. Higher chromium raises the pitting resistance equivalent somewhat, but not enough to make 310S a marine material. For seawater service the duplex grades such as S32205 or the super-austenitic grades are the appropriate choice.

Q: Why is 310S more prone to weld cracking than 304?
Because it solidifies as fully austenite with no delta ferrite, and austenite has low solubility for sulphur and phosphorus. Those elements segregate to the solidification boundaries as low-melting films, and the shrinkage strain of the weld tears them. Low heat input, clean base metal, controlled interpass temperature and a suitable filler, sometimes nickel-base, are the standard countermeasures.

Q: Do these grades need post-weld heat treatment?
Normally no. A low-temperature stress relief in the 425 °C to 815 °C range would precipitate carbides and sigma and reduce corrosion resistance and toughness. If thermal treatment is required, it must be a full solution anneal at 1035 °C to 1150 °C with rapid cooling.

Q: How can a buyer tell 309S from 310S on delivery?
Only by chemical analysis, since both are austenitic, non-magnetic and visually identical. A portable X-ray fluorescence analyser will separate them on chromium and nickel content, and the mill test certificate must show the product analysis against the specified range. Relying on grade marking alone is not sufficient for critical high-temperature parts.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry