Oct 10, 2024 Leave a message

Plain Carbon Steel: Composition, Properties and Pipe Selection

What Ordinary Steel Means in Product Standards

Ordinary steel, also called plain carbon steel or mild steel, is the unalloyed base of the whole steel supply chain. It contains no deliberate addition of alloying elements beyond the manganese and silicon needed for deoxidation and strength, and its properties come from carbon content plus hot deformation. In commercial practice the family is described by four product standards: GB/T 700 for general structural carbon steel, ASTM A36/A36M for structural shapes and plate, EN 10025-2 for non-alloy structural steels such as S235JR and S355JR, and ASTM A53/A53M and ASTM A106/A106M for pipe. All of them work within a narrow chemical window: carbon from about 0.06 to 0.38 percent and sulphur and phosphorus controlled at low levels.

The commercial attraction is straightforward. Low carbon means low deformation resistance, so a billet or slab can be rolled to finished size in a short, simple sequence of heating, rolling and controlled cooling, with no quenching, tempering or other heat treatment afterwards. Productivity is high, scrap generation is low, quality control variables are few, and the material is available in every product form from strip and wire rod to plate, section, hollow section and seamless tube. The trade-off is equally clear: because nothing but carbon and manganese carries the strength, ordinary steel has modest strength, no elevated-temperature creep resistance, no corrosion resistance beyond what a coating provides, and hard limits on the thickness that can be welded without preheat.

Composition Limits That Define the Family

The chemical definition is what separates ordinary steel from alloy and from stainless steel. Nominal carbon runs from 0.06 percent in low-carbon drawing and forming grades up to about 0.38 percent in the higher-strength structural grades, and steels above roughly 0.60 percent carbon pass into tool and spring territory where toughness falls sharply. Manganese sits between 0.25 and 1.70 percent and is treated as a normal element rather than an alloying addition. Silicon is usually below 0.35 percent in structural grades and below 0.10 percent where galvanizing or deep drawing is involved. Aluminium is added in small amounts to kill the steel and refine grain size; the acid-soluble aluminium content is often specified as a minimum for fine-grain practice.

Sulphur and phosphorus are the decisive impurities. They are unavoidable in bulk steelmaking, and ordinary structural grades tolerate them only within tight caps, commonly 0.045 to 0.050 percent each in general structural steel, tightening to 0.035 percent and then to 0.025 percent as impact toughness or weld quality requirements rise. Sulphur forms manganese sulphide stringers that act as fracture initiation sites and give a strongly directional ductility, so plate that performs well in the rolling direction can fail in through-thickness tension. Phosphorus segregates to grain boundaries during slow cooling and raises the ductile-to-brittle transition temperature, which is why impact-tested grades restrict it more strictly than general structural grades. Steels for the coldest service, such as ASTM A333 low-temperature pipe, add nickel and demand very low sulphur and phosphorus simultaneously.

Grade Comparison Table for Plain Carbon Steel Products

Grade and standard Typical carbon, max percent Minimum yield strength Tensile strength range Typical use
Q195, GB/T 700 0.12 195 MPa 315 to 430 MPa Light sections, wire, general forming
Q235B, GB/T 700 0.20 235 MPa (16 mm and under) 370 to 500 MPa Structural fabrication, general purpose
Q275B, GB/T 700 0.24 275 MPa 410 to 540 MPa Higher-load frames, machine parts
S235JR, EN 10025-2 0.17 to 0.20 depending on thickness 235 MPa 360 to 510 MPa General structures with 27 J at 20 degrees C
S275JR, EN 10025-2 0.18 to 0.21 275 MPa 410 to 560 MPa Medium-strength structures
ASTM A36/A36M 0.26 250 MPa 400 to 550 MPa Bolted and welded building frames
ASTM A106 Grade B 0.30 240 MPa 415 MPa minimum Seamless pipe for high-temperature service
API 5L Grade B PSL1 0.28 245 MPa 415 to 760 MPa General pipeline transmission

The Three-Stage Process and Why Cost Stays Low

The metallurgical reason ordinary steel is cheap is that its whole process window sits in a single phase field. The slab is soaked at roughly 1200 degrees C, hot rolled above the austenite-to-ferrite transformation temperature, and cooled in air. No austenitizing furnace, quench tank or tempering furnace is required, so energy consumption per tonne is low. Because the material is soft and ductile in the rolling temperature range, rolling loads are moderate, roll wear is acceptable, and continuous casting followed by direct rolling is practical. This is the basis of continuous, high-speed production in coil, bar and section mills.

The same simplicity fixes the limits. Without alloying or accelerated cooling, the maximum yield strength achievable in the as-rolled condition in commercial plain carbon product is around 275 to 355 MPa, and that upper end already needs controlled rolling. Without a normalizing or quench-and-temper step, there is no way to guarantee uniform properties in very heavy sections, because the core cools too slowly. And without alloy carbides, service temperature is limited to roughly 400 degrees C for sustained loading; above that, plain carbon steel begins to spheroidize its carbides and lose strength rapidly, which is why high-temperature pipe is specified as Cr-Mo or austenitic stainless instead.

Product Forms and How They Reach the Fabricator

Ordinary steel is supplied as plate, strip or coil, structural sections, bar, wire rod, and tubular products. Each form has its own tolerance and flatness rules that matter more than the grade in day-to-day purchasing. Plate thickness tolerances, crown and flatness are governed by the producing standard; for pipe, the important dimensional parameters are outside diameter, wall thickness tolerance, straightness, out-of-roundness and end squareness, and the weight tolerance per bundle. Buyers who compare offers should convert everything to a delivered-mass basis, because a supplier working at the plus side of the thickness tolerance sells more tonnes per metre than one working at nominal, and the pipe will weigh accordingly.

Ordinary steel tube divides into two distinct families. Seamless tube made from a pierced billet, covered by ASTM A106 or EN 10216-1, has no weld seam and is used where pressure integrity or forming is critical. Welded tube, either electric resistance welded or submerged arc welded, is made from strip; the ERW seam is normalized or left as-welded depending on grade, and its quality is verified by flattening and drift tests rather than by pressure testing alone. The weld seam is the part of the product most sensitive to chemistry and to mill setup, because sulphur and phosphorus segregate differently there and secondary phases can form.

Weldability and Fabrication Behaviour

Plain carbon steel is the easiest structural steel to weld, but it is not free of risk. Because strength is carried by carbon, the hardenability of a given grade rises with carbon content and section thickness, and thick joints can form hard martensite in the heat-affected zone if preheat is insufficient. Working to a welding procedure qualified under ISO 15614-1 or ASME BPVC Section IX, with heat input, preheat and interpass temperature defined, is the reliable control. For carbon contents up to about 0.20 percent and modest thickness, celulosic or rutile consumables work with little or no preheat in shop conditions; above that, low-hydrogen consumables and preheat of 100 to 150 degrees C are usual.

Other fabrication characteristics follow from the low alloy content. Ordinary steel cold forms readily, so tube can be bent, swaged and flared, but the same low strength means it work hardens only modestly and a formed joint cannot be relied on for leak tightness without a proper fitting. It responds well to hot-dip galvanizing because the silicon content is normally below the level that produces a thick, brittle coating, yet high-silicon heats, above roughly 0.25 percent Si, give an excessively thick and poorly adherent zinc layer; this is the single most common galvanizing complaint on plain carbon fabricated assemblies. Machinability is moderate, and free-machining variants rely on resulphurization, which is incompatible with weld quality.

Inspection, Certification and Acceptance

A typical inspection package for plain carbon steel includes the heat analysis, product analysis if requested, tensile test with yield strength, tensile strength and elongation, bend or flattening test for tube, and impact testing where the grade requires it. General technical delivery conditions in EN 10021 define what may be retested and how, and EN 10204 type 3.1 certificates are the normal commercial basis. Dimensional inspection covers length, straightness, wall thickness at the ends and mid-body, and where relevant the weld seam. Non-destructive testing is not routine for ordinary structural steel but can be ordered to ISO 10893 series for tube or ASTM E213 for ultrasonic examination of heavier wall.

Two acceptance details are often overlooked. First, the specified mechanical properties apply to the test piece in the delivery condition, so a pipe that is subsequently normalized or hot-dip galvanized may no longer meet the original yield strength and should be re-verified if the design depends on it. Second, mass tolerance is a commercial as well as a technical variable: the permitted deviation between theoretical and actual mass can be several percent, and on a large order that is a real cost item that should be settled in the contract rather than argued at delivery.

Where Ordinary Steel Stops Being the Right Choice

Ordinary steel is the correct answer for building frames, general mechanical structures, low-pressure fluid lines, culverts, scaffolding, furniture frames and countless everyday products. It becomes the wrong answer under four conditions: sustained service above roughly 400 degrees C, where creep and graphitization appear; wet corrosive service, where a coating system is a maintenance liability rather than a solution; low-temperature service below roughly minus 20 degrees C, where Charpy energy must be guaranteed by a nickel-bearing or fine-grain grade; and high-pressure or sour service, where the product standard itself excludes plain carbon material in favour of a qualified pressure or line pipe grade.

FAQ

Q: Is ordinary steel the same as carbon steel?
Ordinary steel is a subset of carbon steel. All ordinary steel is carbon steel, but carbon steel also covers higher-carbon grades for springs, tools and wire, which fall outside the structural family described by GB/T 700, EN 10025-2 or ASTM A36/A36M because their carbon and hardness levels make them unsuitable for welding and general structural use.

Q: Why are sulphur and phosphorus limited to 0.035 to 0.05 percent?
Sulphur forms manganese sulphide inclusions that reduce ductility, particularly in the through-thickness direction, and increase the risk of cracking during welding. Phosphorus segregates to grain boundaries and raises the ductile-to-brittle transition temperature. Holding both at or below about 0.045 percent gives adequate toughness for general structural service; impact-tested and low-temperature grades require tighter limits.

Q: Can ordinary steel pipe be used for pressure service?
Only where a pressure pipe standard permits it. ASTM A106 Grade B and API 5L Grade B are ordinary carbon steel chemistries but are manufactured, tested and marked against pressure piping specifications, including hydrostatic testing and non-destructive examination options. Generic structural tube to EN 10219 or ASTM A500 is not a pressure product and should not be substituted.

Q: What happens to plain carbon steel above 400 degrees C?
Carbides begin to spheroidize and the ferrite matrix recovers, so tensile and creep strength fall progressively. Oxidation also accelerates. Sustained high-temperature service therefore requires Cr-Mo grades such as ASTM A335 P11 or P22, or austenitic stainless steel, where stable carbides and a chromium oxide layer provide strength and oxidation resistance.

Q: Does galvanizing change the mechanical properties of ordinary steel?
The zinc bath operates near 450 degrees C, well below the tempering range of plain carbon steel, so strength is essentially unaffected. However, the thermal cycle can relax residual stresses and slightly reduce the strength of cold-formed tube, and high-silicon heats produce thick brittle coatings. Coating mass should be checked against ASTM A123/A123M or ISO 1461.

Q: How do I compare offers for ordinary steel tube?
Compare the same grade and delivery condition, the actual wall thickness against the permitted tolerance, the mass tolerance and theoretical versus actual weight basis, the inspection level and certificate type, and the end finish. Two offers at the same headline price per tonne can differ materially in delivered mass, testing scope and dimensional compliance.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry