What Is a Trunnion Mounted Ball Valve
A trunnion mounted ball valve is a quarter turn isolation valve in which the ball is anchored to the valve body through an upper and a lower trunnion. The trunnions take the thrust created by line pressure, so the ball turns on fixed bearings instead of being pressed against the downstream seat. Because the ball is supported rather than floating, the seating load is produced by dedicated springs and by piston action, and the operating torque stays low even on large diameter, high pressure pipelines.
The design is standardised through API 6D and ISO 14313, which set out pressure ratings, wall thickness rules, materials, inspection and pressure testing for pipeline valves. Fire safety and static electricity are covered by API 607 or ISO 10497 and by the anti-static provisions of API 6D.
Construction and Working Principle
The ball is centred between two seat rings. Each seat is pre-loaded by a spring and then energised by line pressure, so the seal works in both directions: the valve isolates flow whichever side carries the pressure. A cavity relief path prevents trapped body pressure from exceeding the shell design value.
| Parameter | Typical range or reference |
|---|---|
| Nominal size | NPS 2 to NPS 48 and above |
| Pressure class | Class 150 to Class 2500 |
| Body styles | Two piece, three piece, top entry |
| Seat design | Spring loaded, single or double piston effect |
| End connections | ASME B16.5 and ASME B16.47 flanges, ASME B16.25 butt weld |
| Pressure testing | Shell and seat tests to API 6D or API 598 |
| Fire qualification | API 607 or ISO 10497 |
| Temperature limits | Governed by the pressure and temperature rating in ASME B16.34 |
Performance Advantages
Bidirectional sealing, verified by a seat test in each direction.
Low operating torque, which allows electric, pneumatic and hydraulic actuators to be sized economically.
Reduced seat wear, because line pressure no longer drives the ball into the seat.
Double block and bleed capability, so the body cavity can be drained while both seats remain closed.
Fire safe and anti-static construction, using a metal or graphite secondary seal and a conductive path between ball, stem and body.
Full bore or reduced bore options to suit pigging and pressure loss requirements.
Applications
Trunnion mounted ball valves are used on crude oil and natural gas transmission lines, compressor and pump stations, metering skids, tank farms and high pressure process lines in refineries and petrochemical plants. They are equally common on large diameter water and slurry pipelines, where a floating ball design would demand an oversized operator.
Selection, Installation and Maintenance Points
Choose full bore where pigging or unrestricted flow is required, and reduced bore where a small pressure loss is acceptable. Match the seat and seal material to the actual fluid: soft seats made from polytetrafluoroethylene are limited by temperature, while metal seats tolerate higher temperatures with a wider permitted leakage allowance. Vent the body cavity before maintenance, support large valves so that piping loads are not carried by the flange, and check that the operator orientation allows the valve to be stroked over its full quarter turn.
FAQ
Q: What is the difference between a trunnion mounted and a floating ball valve?
In a floating ball valve the ball is held only by the two seats, and line pressure presses it into the downstream seat. In a trunnion mounted valve the ball is held by bearings, so the design suits larger sizes and higher pressure classes at lower torque.
Q: Which standards apply to trunnion mounted ball valves?
API 6D and ISO 14313 for pipeline valves, ASME B16.34 for pressure and temperature ratings, API 607 or ISO 10497 for fire type testing, and API 598 or API 6D for pressure testing.
Q: What does double block and bleed mean?
Both seats seal independently and the body cavity can be drained through a bleed connection, so upstream and downstream flow are isolated at the same time.
Q: Can the valve be operated by an actuator?
Yes. Low torque and a defined mounting flange make the design suitable for electric, pneumatic and hydraulic actuators, including spring return fail safe arrangements.
Q: How is the body cavity protected from overpressure?
A relief path in the seat or body releases trapped cavity pressure to the low pressure side before the shell design pressure is reached.
Q: Are metal seated trunnion valves suitable for abrasive media?
Metal seats tolerate abrasive and high temperature duty better than soft seats, but they are matched with a controlled leakage allowance, so the process requirement should be stated at the enquiry stage.





